Rear Panel

24

23

25

26

27

28

29

30

23EFFECTS LOOP

1/4" Send and Return jacks for the effects loop.

24CABINET IMPEDANCE SELECTOR SWITCH

This three-position switch allows appropriate selection of speaker cabinet impedance. If two loudspeaker enclosures of equal impedance are used, the switch should be set to half the individual value. For example, two 16-ohm enclosures necessitate an 8-ohm setting, while two 8-ohm enclosures would require a 4-ohm setting. Minimum speaker impedance is 4 ohms. The stock setting for the internal speaker is 16 ohms.

25SPEAKER OUTPUTS

These paralleled 1/4" mono (TS) jacks are provided for the connection of speaker enclosure(s). Again, minimum speaker impedance is 4 ohms. The CABINET IMPEDANCE SWITCH (24) should be set to match the load of the speaker cabinet(s).

26MSDI™

Microphone Simulated Direct Interface. Peavey's exclusive MSDI simulates teh sound of a microphone placed approximately 8" from loudspeaker cone, allowing the user to send a clean signal to the mixing console. This is a non-powered output and safe for use with any mixing console.

27GROUND LIFT

Engage this switch if the mix engineer is hearing a hum in the MSDI output This should eliminate the hum.

28FOOTSWITCH

1/4" input for the optional footswitch.

29FUSE

A fuse is located within the cap of the fuse holder. This fuse must be replaced with one of the same type and value to avoid damaging the amplifier and voiding the warranty. If the amp repeatedly blows the fuse, it

should be taken to a qualified service center for repair.

WARNING: THE FUSE SHOULD ONLY BE REPLACED AFTER THE POWER CORD HAS BEEN DISCONNECTED.

30IEC MAINS CONNECTOR

This is a standard IEC power connector. An AC mains cord having the appropriate AC plug and ratings for the intended operating voltage is included in the carton. The mains cord should be connected to the amplifier before connecting to a suitable AC outlet.

U.S DOMESTIC AC MAINS CORD

The mains cord supplied with the unit is a heavy-duty, 3-conductor type with a conventional 120 VAC plug with ground pin. If the outlet used does not have a ground pin, a suitable grounding adapter should be used, and the third wire should be grounded properly.

Never break off the ground pin on any equipment. It is provided for your safety.

NOTE: FOR UK ONLY

If the colors of the wires in the mains lead of this unit do not correspond with the colored markings identifying the terminals in your plug, proceed as follows: (1) The wire that is colored green and yellow must be connected to the terminal that is marked by the letter E, the Earth symbol, colored green, or colored green and yellow. (2) The wire that is colored blue must be connected to the terminal that is marked with the letter N or the color black. (3) The wire that is colored brown must be connected to the terminal that is marked with the letter L or the color red.

10

Page 9 Page 11
Page 10
Image 10
Peavey 6505 manual Effects Loop, Cabinet Impedance Selector Switch, Speaker Outputs, Ground Lift, Footswitch, Fuse
Page 9 Page 11

6505 specifications

The Peavey 6505 amp head has emerged as an iconic staple in the world of high-gain guitar amplification, cherished by rock and metal musicians alike. Known for its aggressive sound and robust build quality, this amp addresses the needs of players desiring powerful tone and versatility.

One of the main features of the Peavey 6505 is its dual-channel design. The two channels, labeled as Lead and Clean, allow musicians to seamlessly switch between a pristine clean tone and a searing, high-gain drive. The Lead channel is renowned for its rich, saturated distortion, making it perfect for heavy riffs and solos. It offers a three-band EQ, allowing users to sculpt their tone with precision.

The Peavey 6505 is powered by four EL34 tubes in the power section, coupled with a pair of 12AX7 preamp tubes. This tube configuration plays a crucial role in delivering the signature Peavey tone, characterized by massive low-end response and sharp highs. The amp's power output, with 120 watts of tube-driven power, ensures that it can fill even the largest venues with rich harmonics and clear articulation.

Another key technological advancement in the 6505 is its resonance control knob. This feature enhances the amp’s responsiveness by adjusting the low-end frequencies, allowing players to achieve a tighter or looser sound based on their preferences. Additionally, the Presence control adds more bite to the high frequencies, enabling players to tailor their tone for different playing styles.

The Peavey 6505 also includes an effects loop, which is an essential feature for integrating pedals and other effects into one’s setup. This allows musicians to maintain the integrity of their sound while utilizing various effects without compromising the amp's tonal character.

Durability and reliability are hallmarks of the Peavey brand, and the 6505 follows suit with a rugged construction designed for the rigors of live performance. The sturdy chassis and high-quality components ensure that this amp can withstand the demands of extensive touring.

In summary, the Peavey 6505 is more than just a high-gain amplifier; it is a versatile tool that allows musicians to explore a wide range of tones while delivering exceptional sound quality. Its powerful features, robust construction, and signature tone continue to make it a favorite among guitarists looking to push the boundaries of their sound.
Top Page Image Contents