Mounting and Removing Flat Panel Screen

AA

 

WARNING

 

 

 

 

 

 

Always use an assistant or mechanical lifting equipment to safely lift and position the flat panel screen.

Do not tighten screws with excessive force. Overtightening can cause damage to mount. Tighten screws to 40 in. • lb (4.5 N.M.) maximum torque.

Be careful not to pinch fingers when pushing screen from the bottom.

BB

&

CC

DETAIL 1

RATCHET

HANDLE

3

Tension Adjustment of Ratchet Handle: Adjust

 

 

 

tension in tilt brackets (BB & CC) by rotating

AA

BB

 

 

ratchet handle. NOTE: If obstruction prevents

 

 

ratchet handle from rotating, pull handle out while

 

 

turning will allow handle to reposition without

 

&

 

 

tightening. Release and turn handle to tighten or

 

CC

 

 

loosen.

SAFETY/

 

 

Mounting Screen: Ratchet handle must be in the

SECURITY

 

 

 

SCREW

 

 

 

up or down position or interference will occur while

 

fig 3.1

 

 

CROSS SECTION

 

hooking tilt brackets to wall plate (AA). Slowly hook

 

 

 

 

 

tilt brackets (BB & CC) onto wall plate (AA) and

 

 

 

 

swing screen down as shown in fig. 3.1. Tilt bracket

 

 

 

 

hooks must fully engage wall plate as shown in

 

 

 

 

detail 1. Using phillips screw driver or security allen

 

 

 

 

wrench (FF), turn safety/security screws on tilt

 

 

 

 

brackets (BB & CC) clockwise till screw tip securely

 

 

 

 

contacts wall plate as shown in cross section.

 

 

 

Screen Adjustment: Screen can be adjusted horizontally by loosening safety/security screws on tilt brackets (BB & CC) three full turns. Adjust screen as shown in figure 3.2. Tighten safety/ security screws on tilt brackets till screw tip securely contacts wall plate as shown in cross

section.

Removing Screen: To remove screen from mount,

loosen safety screws, swing screen away fromfig 3.2 mount, and lift screen off of mount.

Adjusting the Tilt Angle of the Flat Panel

IncreLok™

 

Screen

 

TILT

 

 

 

 

LOCKING

LOCATOR

4

For preset tilt angles use Increlok™ and for

 

SCREW

 

HOLE

 

 

 

custom tilt angle use ratchet handle.

 

 

 

 

 

INCRELOK: The screen can be locked into a

 

 

 

 

 

pre-set tilt position of -5°, 0°, 5°, 10° or 15°. Use

 

 

 

 

 

locator hole to find tilt position hole and tilt screen

 

 

 

 

 

to align holes. Tighten IncreLok™ tilt locking

 

TILT

 

RATCHET

 

screws on both tilt brackets to lock tilt as shown in

 

 

 

POSITION

 

HANDLE

 

detail 2.

 

 

 

HOLES

DETAIL 2

 

Ratchet Handle: Loosen ratchet handle (refer

 

 

 

 

 

to step 3 for tension adjustment of handle). Push

 

 

 

 

 

or pull from top or bottom of screen to adjust tilt

 

 

 

 

 

as shown in fig. 4.1. The tilt can be adjusted to a

 

 

 

fig 4.1

 

maximum of 15° forward or 5° backward.

 

 

 

 

9 of 38

 

 

ISSUED: 11-21-07 SHEET #: 202-9255-5 05-12-10

 

 

 

 

 

© 2009, Peerless Industries, Inc. All rights reserved.

 

 

All other brand and product names are trademarks or registered trademarks of their respective owners.

 

 

 

 

 

Peerless Industries, Inc.

3215 W. North Ave. Melrose Park, IL 60160 www.peerlessmounts.com

Page 9
Image 9
Peerless Industries SWS320/SI manual Mounting and Removing Flat Panel Screen, Adjusting the Tilt Angle of the Flat Panel