dell’impianto elettrico.
•Non lasciare le batterie o il veicolo vicino a fonti di calore come caloriferi, caminetti, etc.
•Proteggere il veicolo da acqua, pioggia, neve etc.; usarlo su sabbia o fango potrebbe causare danni a pulsanti, motori e riduttori.
•Se il veicolo agisce in condizioni di sovraccarico, come su sabbia soffice, fango o terreni molto sconnessi, l’interruttore di sovraccarico toglierà immediatamente potenza. L’erogazione di potenza riprenderà dopo alcuni secondi.
•Lubrificare periodicamente (con olio leggero) parti semovibili come cuscinetti, sterzo etc.
•Le superfici del veicolo possono essere pulite con un panno umido e, se necessario, con prodotti di uso domestico non abrasivi.
•Le operazioni di pulizia devono essere effettuate solo da adulti.
•Non smontare mai i meccanismi del veicolo o i motori, se non autorizzati dalla PEG PEREGO.
Conforme a EN 50088
Batteria ricaricabile da 6V 4,5Ah al piombo sigillata. 1 motore da 60 W
SICUREZZA
ATTENZIONE! LA SUPERVISIONE DI UN ADULTO É SEMPRE NECESSARIA.
•Non adatto ai bambini di età inferiore ai 24 mesi per caratteristiche funzionali.
•Non usare il veicolo su strade pubbliche, dove c’è traffico e macchine parcheggiate, su pendenze ripide, vicino a gradini e scale, corsi d’acqua e piscine.
•I bambini devono sempre indossare scarpe durante l’uso del veicolo.
•Quando il veicolo è operativo fare attenzione affinché i bambini non mettano mani, piedi o altre parti del corpo, indumenti o altre cose, vicino alle parti in movimento.
•Non bagnare mai componenti del veicolo come motori, impianti, pulsanti, etc.
•Vicino al veicolo non usare benzine o altre sostanze infiammabili.
•Il veicolo deve essere usato esclusivamente da un solo bambino.
REGOLE PER UNA GUIDA SICURA
DIVERTIMENTO SENZA INTERRUZIONI: tenete sempre un set-batterie carico di ricambio pronto all’uso.
Per la sicurezza del bambino: prima di azionare il veicolo, leggere e seguire attentamente le seguenti istruzioni.
•ATTENZIONE:
Controllare che tutte le borchie di fissaggio delle ruote siano ben salde.
•MARCIA AVANTI:
Con entrambe le mani sul manubrio premere il pedale dell’ acceleratore;
il veicolo si mette in moto ad una velocità di circa 4 Km/h.
•FRENO:
Per frenare alzare il piede dal pedale acceleratore, il freno entrerà in funzione automaticamente.
Insegnate al vostro bambino un uso corretto del veicolo per una guida sicura e divertente.
•Prima di partire assicurarsi che il percorso sia sgombro da persone o cose.
•Guidare con le mani sul manubrio e guardare sempre la strada.
•Frenare per tempo per evitare scontri.
•ATTENZIONE! se il veicolo agisce in condizioni di sovraccarico, come su sabbia soffice, fango o terreni molto sconnessi, l’interruttore di sovraccarico toglierà immediatamente potenza. L’erogazione di potenza riprenderà dopo alcuni secondi.
PROBLEMI?
IL VEICOLO NON FUNZIONA?
•Verificare che non ci siano cavi scollegati sotto la piastra dell’ acceleratore.
•Controllare il funzionamento del pulsante dell’acceleratore ed eventualmente sostituirlo.
•Controllare che la batteria sia attaccata all’ impianto elettrico.
IL VEICOLO NON HA POTENZA?
•Caricare le batterie. Se dopo la ricarica il problema persiste far controllare le batterie ed il
caricabatterie da un centro assistenza.
ENGLISH
•PEG PEREGO® thanks you for choosing this product. For over 50 years, PEG PEREGO has been taking children for an outing: first with its famous baby carriages and strollers, later with its pedal and battery operated toy vehicles.
•Read this instruction manual carefully to learn the use of this vehicle and to teach your child safe and enjoyable driving. Please keep this manual for use as a reference in the future.
•Our toys conform with the safety requirements provided by the Council of the EEC, of the T.Ü.V.; of the I.I.S.G. Istituto Italiano Sicurezza Giocattoli, and the U.S. Consumer Toy Safety Specification F963.
Peg Perego S.p.A. is an ISO 9001 certified company.
The fact that we are certified provides a guarantee of our honesty for our customers, and fosters trust in the company’s way of working.
•Peg Perego reserves the right to modify or change their product. Price, literature, manufacturing processes or locations or any combination of these above mentioned entities may change at any time for any reason without notice with impunity.
Years 2-4
CUSTOMER SERVICE
PEG PEREGO offers after-sales services, directly or with a network of authorized service centers for repairs or replacement parts. See the back cover of this instruction manual for a list of service centers.
Peg Perego is at the consumer's service, meeting every need in the best way possible. This is why our customers' opinions are so important and valuable to us. We would be very grateful if you would kindly fill in the CUSTOMER SATISFACTION QUESTIONNAIRE after using one of our products. You will find the questionnaire on the Internet at "www.pegperego.com/SSCo.html.en-UK".
Please note any observations or suggestions you may have on the questionnaire.
ASSEMBLY INSTRUCTIONS
ADULT ASSEMBLY REQUIRED.
USE CARE WHEN UNPACKING AS COMPONENTS TO BE ASSEMBLED MAY POSE A SMALL PARTS/SHARP EDGE HAZARD.
BATTERY ALREADY INSTALLED IN VEHICLE.
ASSEMBLY
1 • Check the forecarriage to be sure it is correctly fastened at points (A). Remove the protective caps (B).
2 • Insert an iron washer on the pin of the forecarriage, as shown in the figure.
3 • (1)Insert one of the two front wheels: make sure you use the wheel shown in Figure A.
(2)Insert an iron washer.
4 • Insert a self-locking washer on the provided tool (shown in the figure). Caution: The tabs of the self-locking washer must face the inside of the tool (see small picture A). NOTE: the bag contains 8 self-locking washers. Keep 4 of them apart as spare washers.
5 • Fasten the wheel as shown in the figure, pushing the self-locking washer down completely.
6 • Snap on the stud cover. Perform the same operations as the ones in Figure 2 for the other front wheel.
7 • Insert a self-locking washer on the provided tool (shown in the figure). Caution: The tabs of the self-locking washer must face the inside of the tool (see small picture A).
8 • Remove the grey protective caps at the ends of the rear axle. Insert the axle on the tool as shown in the figure.
9 • (1)Insert an iron washer on the axle. (2)Insert
the axle into one of the two rear wheels: make sure you use the wheel shown in Figure A.
10 • Insert the axle with the wheel into the hole of the gearmotor, pressing to be sure it exits from the opposite side of the vehicle.
11 • Turn the wheel slightly to match up the gearmotor pentagon with the one on the wheel (Figure shows incorrect fastening of the wheel).
12 • Insert the bushing as shown in the figure, working from the other side of the shaft until it is hooked to the body.
13 • Insert an iron washer as shown in the figure.
14 • Reposition the tool (used previously to insert the self-locking washer - see Figure 7) on the axle from the wheel side. Place the vehicle on one side, keeping the wheel underneath. Make sure the tool cannot shift.
15 • (1)Position the remaining wheel end insert an iron washer. (2)Insert a self-locking washer on the provided tool (shown in the figure).
Caution: The tabs of the self-locking washer must face the inside of the tool (see small picture A). (3)Fasten the wheel as shown in the figure, pushing the self-locking washer down completely.
16 • Snap on the remaining stud covers on both sides.
17 • Position the handle support.
18 • Slide on the handle, orienting it as shown in the figure.
19 • Fasten the handle with a washer and screw.
20 • Position the cap by inserting the tongue (1) into the rear notch of the support. Turn the cap
(2).
21 • Apply the silver decal.
22 • Apply the glass on the front light till it clicks.
23 • Place the trunk support on the vehicle, and fasten it with the 4 screws that come with it.
24 • Place the trunk on the support, fitting it into the special hooks, as shown in the figure. Pull the trunk all the way towards you, to fit it into place (detail A).
25 • Rotate the red catch behind the saddle until bringing it to the position shown on figure. A: the saddle is locked. B: the saddle can be lifted. Lift up the saddle.
26 • Connect the two plugs.
27 • Reposition the saddle by sliding the two pins into the holes on the tank. Turn the red catch behind the saddle in order to fasten it. The vehicle is ready to use.
VEHICLE FEATURES AND INSTRUCTIONS FOR USE
28 • GEARSHIFT LEVER: Your child will have fun pretending to change gears using this gearshift lever, which can be rotated into two positions.
29 • ACCELERATOR/ELECTRIC BRAKE PEDAL: The vehicle brakes automatically when your child lift his/her foot off the pedal.
REPLACING THE BATTERY
30 • Rotate the red catch behind the saddle until bringing it to the position shown on figure 25 (figure B). Lift up the saddle. Unplug the terminals. Unscrew the battery fastener.
31 • Lower the catch (1) and, at the same time, push the battery fastener as indicated by the arrow
(2)to release it. Remove the battery fastener. 32 • Replace the battery. (NOTE: The replacement
battery – separately available – is a 6v/ 8Ah battery pack). Replace and screw back on the battery fastener. Connect the two plugs. CAUTION: When you have finished, remember to close and fix down the seat.
BATTERY RECHARGE
WARNING: BATTERY CHARGING AND EVERY OTHER OPERATION ON THE ELECTRICAL SYSTEM MUST BE CARRIED OUT BY ADULTS ONLY.
THE BATTERY CAN ALSO BE CHARGED WITHOUT REMOVING IT FROM THE TOY.
33 • Unplug vehicle wiring terminal A from battery terminal B, by pressing terminals on side and pulling apart.
34 • Plug the battery charger terminal to a wall outlet following the instructions enclosed. Connect the plug B to the battery charger plug C.
35 • Once the charge is completed unplug recharger from wall outlet. Unplug recharger cord terminal C from battery terminal B.
36 • Plug battery terminal A into vehicle wiring terminal B. Close saddle.
BATTERY MAINTENANCE AND SAFETY
Before riding, charge your batteries for 18 hours to
