ŘA L L |
W I N D O W S |
Ř A L L |
W I N D O W S |
Ř A L L |
W I N D O W S |
Ř A L L |
W I N D O W S |
Ř A L L |
ŘW I N D O W S |
REMEMBER TO USE APPROPRIATE PERSONAL PROTECTIVE EQUIPMENT.
1 ROUGH OPENING PREPARATION
*OUFSJPS
A.Make sure the bottom of the opening is level.
Note: It is critical the bottom is level for the window to be |
| ||||
installed correctly. |
|
|
| 1A£ | |
|
|
|
| ||
B. Confirm the window will fit in the opening. Measure all four |
| ||||
sides of the opening; |
|
|
|
| |
Standard units: Opening is to be 3/4" larger than the window |
| ||||
in both width and height. |
|
|
|
| |
Performance Upgrade and HurricaneShield: Opening is |
| ||||
to be 1/2" larger than the window in both width and height. | *OUFSJPS | ||||
On larger openings measure the width and height in several | |||||
| |||||
places to confirm the header or studs are not bowed. |
| ||||
Note: |
| ||||
around the perimeter of the opening. Fix any problems | 1B£ | ||||
with the rough opening before proceeding. | |||||
| |||||
BUFS3FTJTUJWF#BSSJFS |
|
|
|
| |
TUDVU | UI | DVU |
| ||
|
|
| |||
| $VUEPXOUPNFFUUIF |
| |||
| ¡DVUPOFBDIDPSOFS |
| |||
OEDVU | UIDVU |
| |||
|
| ||||
| .BLFBDVUVQGSPN |
| |||
£ | FBDIUPQDPSOFSBUB¡ |
| |||
BOHMFUPBMMPXUIFXBUFS |
| ||||
1C |
| ||||
| SFTJTUJWFCBSSJFSUPCF |
| |||
SEDVU | MBQQFEPWFSUIFmOBUUIF | Exterior | |||
| IFBEPGUIFXJOEPX |
| |||
C.Cut the water resistive barrier (1C). See page 10 for
additional cutting patterns. | 1D |
|
D. Fold the water resistive barrier (1D). Fold side flaps into the opening and staple to inside wall. Fold top flap up and temporarily fasten with flashing tape.
E. Apply sill flashing tape #1. Cut a piece of flashing tape 12" longer than the opening width. Apply at the bottom of the opening as shown (1E) so it overhangs 1" to the exterior.
| Note: The tape is cut 12" longer than the width so that it will extend 6" up | ||||||||||||
| each side of the opening. |
|
|
|
|
|
|
|
|
|
|
|
|
F. | Tab the sill flashing tape |
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
| 1E£ |
|
|
| ||||
|
|
|
|
|
|
|
|
| |||||
| and fold. Cut 1" wide tabs at |
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
| |
| each corner (1/2" from each |
|
|
|
|
|
|
|
|
| 1G£ | ||
| side of corner) (1F). Fold tape |
|
|
|
|
|
|
|
|
|
|
|
|
| to the exterior and press |
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
| |||
| firmly to adhere it to the |
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
| |
| water resistive barrier. | 1F£ |
|
|
|
|
|
|
|
| |||
G. Apply sill flashing tape #2. |
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
| ||
Cut a piece of flashing tape
12" longer than the opening width. Apply at the bottom, overlapping tape #1 by at least 1". Do not allow the tape to extend past the interior face of the framing (1G).
Note: The flashing tape may not fully cover the framing members.
