IMPORTANT NOTICE

Because all construction must anticipate some water infiltration, it is important that the wall system be designed and constructed to properly manage moisture. Pella Corporation is not responsible for claims or damages caused by anticipated and unanticipated water infiltration; deficiencies in building design, construction and maintenance; failure to install Pella® products in accordance with Pella installation instructions; or the use of Pella products in wall systems which do not allow for proper management of moisture within the wall systems. The determination of the suitability of all building components, including the use of Pella products, as well as the design and installation of flashing and sealing systems are the responsibility of the Buyer or User, the architect, contractor, installer, or other construction professional and are not the responsibility of Pella.

Pella products should not be used in barrier wall systems which do not allow for proper management of moisture within the wall systems, such as barrier Exterior Insulation and Finish Systems, (EIFS) (also known as synthetic stucco) or other non-water managed systems. Except in the states of California, New Mexico, Arizona, Nevada, Utah, and Colorado, Pella makes no warranty of any kind and assumes no responsibility for Pella windows and doors installed in barrier wall systems. In the states listed above, the installation of Pella products in barrier wall or similar systems must be in accordance with Pella installation instructions.

Product modifications that are not approved by Pella Corporation will void the Limited Warranty.

INSTALLING ROTO COVER AND CRANK

Note: Finish the interior of the window and allow the window to dry before proceeding with these instructions. (To open the window for finishing, partially insert the lock handle into the jamb, unlock the unit, temporarily attach the crank handle and turn to open.)

A. Place the cover over the

 

 

 

operator stud and snap

Pocket End

 

 

into place. Position the

 

 

 

 

 

pocket end of the cover

 

 

 

into place.

 

 

 

Note: If the cover does

Screw Hole

 

not have the screw hole,

 

 

 

 

apply pressure on the

A

Operator Stud

pocket end of the cover

 

 

to snap the cover into

 

 

 

place and proceed to

 

 

 

step C.

Crank Handle

D

 

B. Insert the provided

Operator Stud

 

 

 

 

 

screw into the hole

 

 

 

in the bottom of the

 

 

 

pocket. Use a # 1 Phillips

 

 

 

screwdriver to secure

Set Screw

C

the pocket screw snug

 

 

 

against the bottom of

 

 

 

the pocket to avoid

 

 

 

scratching the crank handle knob. DO NOT over tighten.

B

 

Knob

E

Pocket

C.Use a medium size flat-blade screwdriver to loosen the set screw in the crank handle.

D.Slide the crank handle onto the stud. Unlock, open window, then close and lock window.

E.Fold the crank handle down and check alignment of knob with the pocket.

Note: You may need to adjust the crank position on the stud until the correct alignment is achieved.

F.Open the crank and tighten the set screw.

G.After the final installation, fold the crank over and snap the knob into the pocket.

Note: Even with the window open the crank can be folded to avoid interferring with the window treatments.

Page 6 Page 8
Page 7
Image 7
Pella 80WW0101 warranty Important Notice, Installing Roto Cover and Crank
Page 6 Page 8

80WW0101 specifications

The Pella 80WW0101 window is a prime example of modern window technology, combining aesthetic appeal with superior performance. Designed for both new constructions and replacements, this window emphasizes energy efficiency, durability, and versatility, making it a favorite among homeowners and builders alike.

One of the standout features of the Pella 80WW0101 is its exceptional energy efficiency. This window is equipped with advanced insulating glass technology, offering multiple glazing options that help to reduce energy costs significantly. With Low-E (low emissivity) glass coatings, it minimizes heat transfer, keeping homes comfortable in both winter and summer months. This technology also helps block harmful UV rays, protecting interiors from fading.

The design of the Pella 80WW0101 is equally impressive. It comes in a variety of styles, including single-hung, double-hung, casement, and sliding configurations, making it suitable for diverse architectural designs. The window also boasts a range of color and finish options, allowing homeowners to customize their appearance to match their home’s exterior. The sleek lines and contemporary style enhance a home's curb appeal while ensuring functionality.

Durability is another key characteristic of the Pella 80WW0101. Crafted from high-quality materials, including fiberglass and vinyl, the window is built to withstand the elements, ensuring longevity and minimal maintenance. It resists warping, peeling, and fading, providing peace of mind to homeowners in various climates.

Moreover, the Pella 80WW0101 incorporates innovative technologies that enhance user convenience and safety. Features such as easy-to-operate locking mechanisms and optional integrated shades or blinds offer added practicality. Homeowners also appreciate the sound-dampening capabilities, which can help reduce outside noise for a more tranquil indoor environment.

The Pella 80WW0101 not only addresses performance and durability but also meets strict industry standards for safety and quality. With its blend of aesthetic design and advanced technology, it serves as a functional yet stylish addition to any home. Whether for new builds or window replacements, this model stands out as an ideal choice for those seeking a reliable, energy-efficient, and attractive window solution.
Top Page Image Contents