1.Do not connect system to a high pressure or city water system.
2.Use equipment only in a pool or spa installation.
3.Trapped air in system can cause explosion. BE SURE all air is out of system before operating or testing equipment.
Before pressure testing, make the following safety checks:
• | Check all clamps, bolts, lids, and system accessories |
| before testing. |
• | Release all air in system before testing. |
• Water pressure for test must be less than 25 PSI | |
| (7.5 kg/cm2). |
• | Water Temperature for test must be less than 100o F. |
| (38o C). |
• | Limit test to 24 hours. After test, visually check system |
| to be sure it is ready for operation. Remove trap lid and |
| retighten hand tight only, see Figure 1. |
| NOTICE: These parameters apply to |
|
|
|
|
|
|
|
|
|
|
|
|
|
| MP |
|
|
|
|
|
|
|
|
|
|
|
|
| N | PU | S | |
|
|
|
|
|
|
|
|
|
|
| O |
| RSOW | ||
|
|
|
|
|
|
|
|
|
| IB |
| OAWR |
| ||
|
|
|
|
|
|
|
|
| R |
| ERNR |
|
| ||
|
|
|
|
|
|
|
| O |
| AE |
|
|
| ||
|
|
|
|
|
|
|
| S | TN |
|
|
| |||
|
|
|
|
|
|
| G |
|
| W |
|
|
| ||
|
|
|
|
|
|
|
| B |
|
|
|
| |||
|
|
|
|
|
| IN |
|
| EE |
|
|
| |||
|
|
|
|
|
|
| TSW |
|
|
|
|
| |||
|
|
|
|
|
|
| NE |
|
|
|
|
| |||
|
|
|
|
|
| IGB |
|
|
|
|
|
| |||
|
|
|
| ID |
|
|
| LS |
|
|
|
|
|
|
|
|
|
| E | L |
|
| AN |
|
|
|
|
|
|
| |
TA | T |
| IASRC | EA | RALG |
|
|
|
|
|
|
|
|
| |
RO |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
| CDH |
|
|
|
|
|
|
|
|
|
|
| |
| IS |
|
|
|
|
|
|
|
|
|
|
|
| ||
| D |
|
|
|
|
|
|
|
|
|
|
|
|
| |
Arrows
Tab
Discharge
Port
Figure 1 – Strainer basket cover alignment.
INSTALLATION
Only qualified, licensed personnel should install pump and wiring.
only. For |
NOTICE: Do not start the pump until the strainer basket |
cover is on and the tab, or rib, on the discharge port |
aligns between the arrows. |
IMPORTANT SAFETY INSTRUCTIONS
Discharge Port to Filter or Pool
Bonding Lug
Strainer Basket
Cover
Suction
Port
from
Pool or
Vacuum
Filters
Always follow basic safety precautions with this equipment, including the following.
To reduce the risk of injury, do not per- mit children to use this product unless they are closely supervised at all times.
This pump is for use with permanently installed pools and may also be used with hot tubs and spas if so marked. Do not use with storable pools. A permanently installed pool is constructed in or on the ground or in a building such that it cannot be readily disassembled for storage. A storable pool is con- structed so that it may be readily disassembled for stor- age and reassembled to its original integrity.
SAVE THESE
INSTRUCTIONS
Pump may be bolted to level
foundation or mounting bracket.
Figure 2
NOTICE: Port threads are: Internal - 2" NPT for direct connec- tion to pipe. External -
See Page 13 for Union Kits.
Pump mount must:
Be located away from corrosive or flammable liquids. Have enough ventilation to maintain air temperature at less than the maximum ambient temperature rating (Max. Amb.) listed on the motor model plate. If this pump is installed in an enclosure/pump house, the enclosure must have ade- quate ventilation and air circulation to keep the tempera- ture in the enclosure at or below the motor’s rated ambient temperature whenever the pump is running.
Be solid - Level - Rigid - Vibration free. (To reduce vibra- tion and pipe stress, bolt pump to mount.)
4
