HOOKING UP THE TELEVISION
REMOTE CONTROL BATTERIES
To load the supplied batteries into the remote:
1 Remove the battery compartment door on the back of the remote.
2 After removing the plastic isolation sheet from the battery, place the battery (3V) in the remote. Be sure the (+) and
3 Reattach the battery compartment door.
Lithium battery (3V)
Battery Compartment Door
Remote Control |
|
(shown from the bottom) | Be sure to point the |
| remote at the remote |
| sensor window on the |
| front of the television |
| when using the remote |
| control to operate the |
| television |
NOTE: The plastic isolation sheet must be removed
for the remote control to function.
CABLE/CABLE BOX TV
Your Cable TV input into your home may be a single (75 ohm) cable or use a cable box decoder. In either case the connec-
tion is very simple. Follow the steps below to connect your cable signal to your new television.
Direct Cable Connections:
This connection will supply Stereo sound to the TV.
1 Connect the open end of the round Cable Company sup- plied cable to the 75Ω input on the bottom of the TV. Screw it down finger tight.
Direct Cable Connection:
Cable signal coming from Cable Company (Round 75Ω coaxial cable)
Jack Panel Bottom of TV
Cable Box (w/RF In/Outputs):
This connection will NOT supply Stereo sound to the TV. The sound from the cable box will be mono.
1
2 Using a separate round coaxial cable, connect one end to the
OUT(put) (TO TV) plug on the back of the Cable Box.
3 Connect the other end of the round coaxial cable to the 75Ω input on the bottom of the television. Screw it down fin- ger tight.
NOTE: Be sure to set the OUTPUT CHANNEL SWITCH on the back of the cable box to CH 3 or 4, then tune the cable box on the TV to the corresponding channel. Once tuned, change channels at the cable box, not the television.
Cable Box with RF Inputs and Outputs Connection:
Output Channel Switch
Cable Signal
IN from the
Cable
Company
Round 75Ω
Coaxial Cable
Jack Panel Bottom of TV
Jack Panel Back
of Cable Box
Cable Box (w/Audio/Video Outputs):
This connection will supply Stereo sound to the TV.
1
2 Using an RCA type Video Cable, connect one end of the cable to the Video (yellow) (or ANT, your cable box may be labeled differently) Out jack on the cable box and the other end to the Video end of the composite adapter included with the TV.
3 Using an RCA type Audio Left and Right Cable, connect one end to the left and right Audio Out L & R jacks (red & white) on the cable box. Connect the other ends to the Audio end of the composite adapter cable included with the TV. Connect the adapter into the AV In jack on the bottom of the TV.
NOTE: Use the AV+ button and the Number 1 button on the TV remote control to tune to the AV1 channel for the cable box signal. Once tuned, change channels at the cable box, not the television. Pressing the AV+ button repeatedly will scroll all the AV Input chan- nels, including the presently tuned channel.
Cable Box with Audio/Video Outputs Connection:
Cable Signal IN from the Cable Company
Jack Panel Back
of Cable Box with A/V Outputs
Audio Cables
L & R (Red, White)
Video Cable
(Yellow)
Jack Panel Bottom of TV
ANTENNA TV
Acombination antenna receives normal broadcast chan- nels (VHF
the back of your TV, and that’s where the antenna goes.
1 If your antenna has a round cable (75 ohm) on the end, then you're ready to connect it to the TV.
If your antenna has flat,
2 Push the round end of the adapter (or antenna) onto the 75Ω (ohm) plug on the bottom of the TV. If the round end of the antenna wire is threaded, screw it down finger tight.
Antenna Connection:
Outdoor or Indoor Antenna | 300 to |
(Combination VHF/UHF) | Adapter |
The combination antenna |
|
receives normal |
|
broadcast channels |
|
and |
|
| Twin |
| Lead Wire |
Round 75Ω
Coaxial Cable
from Antenna
2
Jack Panel
Bottom of TV
