Philips 207530 350, 135, 120-150, Minutes, RMS Min, Micro Second Minimum, Per Half Cycle, 71A5993

Philips Lighting Company	www.philips.com	Philips Lighting
200 Franklin Square Drive		281 Hillmount Road
P.O.Box 6800		Markham, Ontario
Somerset, NJ 08875-6800		Canada L6C 2S3
1-800-555-0050		1-800-555-0050
A Division of Philips Electronics North America Corporation		A Division of Philips Electronics Ltd.
Updated 1/08	TDS-207530

Pulse Start Horizontal Metal Halide 350 Watt Lamp (Clear)

Electrical Data (Subject to change without notice)

Lamp Watts (Nominal)	350
Lamp Operating Voltage (rms) (Nominal)3	135
Initial Lamp Voltage Range (rms)6	120-150
Lamp Operating Current (Amps) (rms) (Nominal)	2.83
Lamp Current Crest Factor (Maximum)	1.6
Warm-up Time to 90% of Output	2 Minutes
Re-strike Time for Hot Lamp	6 Minutes
Ballast Type	ANSI M131/E
Ballast Open Circuit Voltage (Minimum)	245 RMS Min.
Pulse PeakVolts	3000 Minimum, 4000 Maximum
Pulse Width @ 90% Peak	1.3 Micro Second Minimum
Pulse Repetition Rate (Minimum)	1 per Half Cycle
Minimum Operating Temperature	-30º C (-22°F)
Advance Transformer Ballast Number	71A5993

1)Approximate lumen values listed are for horizontal operation of the lamp.

2)Measured at 100 hours of life in horizontal position.

3)Measured at rated lamps on a linear reactor. LPW does not include ballast losses.

4)Approximate lumen output at 40% of lamp rated average life.

5) Rated average life is the life obtained, on the average, from large representative groups of lamps in laboratory tests under controlled conditions at 10 or more operating hours per start. It is based on survival of at least 50% of the lamps and allows for individual lamps or groups of lamps to vary considerably from the average.

6) Measured with the lamp operation at rated watts.

Warnings, Cautions and Operating Instructions

R“WARNING:These lamps can cause seriousskin burn and eye inflammation from short wave ultravioletradiationif outer envelopeof the lamp is brokenor punctured.Do not use where people will remainfor more than a few minutesunless

adequateshieldingor other safetyprecautionsare used.Certain lamps that will automaticallyextinguishwhen the outer envelopeis brokenor puncturedare commerciallyavailable." This lamp complieswith FDA radiationperformance standard21 CFR subchapterJ. (USA:21CFR1040.30Canada:SOR/DORS/80-381)

If the outer bulb is brokenor punctured,turn off at once and replace the lamp to avoid possible injury from hazardousshort wave ultraviolet radiation.Do not scratch the outer bulb or subject it to pressureas this could cause the outer bulb to crack or shatter.A partial vacuum in the outer bulb may cause glass to fly if the envelope

is struck.

WARNING:The arc-tubeof metal halide lamps are designed to operate under high pressureand at temperaturesup to 1000ºC and can unexpectedlyrupture due to internal or external factors such as a ballast failure or misapplication. If the arc-tube rupturesfor any reason,the outer bulb may break and pieces of extremely hot glass might be dischargedinto the surroundingenvironment.If such a rupture were to happen,THERE ISA RISK OF PERSONALINJURY,PROPERTY

DAMAGE,BURNSAND FIRE.

Certain lamps that will retainall the glass particlesshould inner arc-tube ruptureoccur are commerciallyavailablefrom PhilipsLightingCompany.

RELAMP FIXTURESATOR BEFORETHE END OF RATEDLIFE. Allowinglamps to operateuntil they fail is not advisedand may increase the possibilityof inner arc tube rupture.

CAUTION: TO REDUCETHE RISK OF PERSONALINJURY,PROPERTY DAMAGE,BURNSAND FIRE RESULTINGFROMAN ARC-TUBERUPTURETHE FOLLOWINGLAMP OPERATINGINSTRUCTIONSMUST BE FOLLOWED.

Lamp Operating Instructions:

1)Turnoff lamps at least once a week for at least 15 minutes in systems which are operating on a continuous basis (24 hours/day-7days/week)FAILURETOTURN. OFF LAMPS FORTHE MINIMUM RECOMMENDEDTIME MAY INCREASE THE POSSIBILITY OF AN INNERARC-TUBE RUPTURE.

2)RELAMP FIXTURESAT OR BEFORETHE END OF RATEDLIFE.Allowing lamps to operate until they fail is not advised and may increase the possibility of inner arc tube rupture.

3)Use only in an enclosed fixture capable of withstandingparticles of glass having temperaturesup to 1000ºC.

4)Before lamp installation/replacement,shut power off and allow lamp and fixture to cool to avoid electrical shock and potential burn hazards.

5)Use only auxiliary equipment meeting Philips and/orANSI standards.Use within voltage limits recommendedby ballast manufacturer.

A.Operate lamp only within specified limits of operation.

B.For total supply load refer to ballast manufacturerselectrical data.

C.All Pulse Start mogul based lamps require a socket rated to withstand a 4000 volt pulse.

6)Periodicallyinspect the outer envelope.Replace any lamps that show scratches, cracks or damage.

7)If a lamp bulb support is used,be sure to insulate the support electricallyto avoid possible decompositionof the bulb glass.

8)Protect lamp base, socket and wiring against moisture,corrosiveatmospheres and excessive heat.

9)Time should be allowed for lamps to stabilize in color when turned on for the first time.This may require several hours of operation,with more than one start. Lamp color is also subject to change under conditions of excess vibration or shock,and color appearance may vary between individual lamps.

10)Lamps may require 2 to 10 minutes to re-light if there is a power interruption.

11)Takecare in handling and disposing of lamps. If an arc tube is broken,avoid skin contact with any of the contents or fragments.

12)Use this lamp only in fixtures that contain a Pulse Start metal halide ballast and are specificallydesigned for use with Pulse Start metal halide lamps.