Philips AJ3957, AJ3959, AJ3958 warranty Setting TIMES, DAY

English CONTROLS/ INSTALLATION

SETTING TIMES, DAY CD

CONTROLS (See figure 1 and 2)

CD PLAYER

1STOP 9

-stops CD playback;

-stops sleep function in CD mode;

-stops the active CD alarm for 24 hours.

2PLAY/ PAUSE 2;

-starts/ pauses CD playback.

3SEARCH ∞, §

-skips CD tracks/ searches for a particular passage.

GENERAL

4SLEEP

-activates and adjusts the sleep time.

5REPEAT ALARM/ BRIGHTNESS CONTROL

-changes the brightness of the display illumination;

-switches off the alarm for a 9 minute period;

-stops sleep function in CD, buzzer or radio mode.

6WEEKEND-SLEEPER

-deactivates alarm 1 and/ or 2 for the weekend.

7Display

-shows the clock/ alarm time and status of the set.

8ALARM 1 MODE/ OFF or ALARM 2 MODE/ OFF

-sets/ reviews/ switches off alarm 1 or 2.

RADIO

9ON/ OFF

-switches the radio on/ off;

-stops sleep function in radio mode;

-stops the active radio alarm for 24 hours.

0FM/ AM

-selects the radio waveband.

SETTING TIMES

!ALARM 1, ALARM 2, TIME

-sets the respective alarm or clock time

@7 , 8

-adjusts clock/ alarm times;

-adjusts the gentle wake minimum and maximum volume level for alarm 1 or 2;

-selects a CD wake up track for alarm 1 or 2.

#VOLUME $, 3

-adjusts the sound level. $Dial lens

%SET DAY

-sets the day for weekend sleeper activation.

^24 HR RESET

-stops the active buzzer, radio or CD alarms for 24 hours.

&LIFT TO OPEN

-opens/ closes CD door.

*TUNING

-tunes to a radio station.

(Pigtail - antenna to improve FM reception. )Power cord - for AC power supply.

The type plate is located on the bottom of the set.

This product complies with the FCC-Rules, Part 15 and with 21 CFR 1040.10. Operation is subject to the following two conditions:

1This device may not cause harmful interference, and

2This device must accept any interference received, including interference that may cause undesired operation.

CAUTION

Use of controls or adjustments or performance of procedures other than herein may result in hazardous radiation exposure or other unsafe operation.

INSTALLATION

Power Supply and Demo mode

1Check if the power voltage, shown on the type plate on the bottom of the set, corresponds to your local power supply. If it does not, consult your dealer or service center.

2Connect the power plug into the wall outlet. The power supply is now switched on and the display will show the PHILIPS demo mode.

™PH..IL..IPS scrolls across the display continuously.

• Press any control (with the exception of

REPEAT ALARM/ BRIGHTNESS CONTROL on the set) to exit the demo mode.

3To disconnect the set completely from the power supply, withdraw the power plug from the wall outlet.

Standby power consumption (clock mode) 3 W

MEMORY BACKUP

The memory backup conveniently allows your day, alarm and clock time settings to be stored for up to 3 minutes when there is a power interruption e.g. AC power failure.

The complete CD clock radio and illumination will be switched off. As soon as the power supply returns, the display will indicate the correct time.

•If power supply returns after 3 minutes, the display will show the PHILIPS demo mode and you will need to re-enter the day, alarm and clock times.

BASIC FEATURES

Illumination brightness

•Press REPEAT ALARM/ BRIGHTNES CONTROL once or

more.

™The brightness of the display will change in this sequence:

LOW ➠ MEDIUM ➠ BRIGHT ➠ LOW...

Volume

Press VOLUME $ or 3 to adjust the volume level. The volume level UO: is indicated as a number from 0-32.

SETTING THE CLOCK AND ALARM TIMES

The time is displayed using the 12 hour clock where the PM indicator lights up (on = PM, off = AM).

1Press TIME, ALARM 1 or ALARM 2 briefly until the respective clock or alarm time display flashes.

2Press and hold down 7, 8 to adjust both the hours and minutes.

•By pressing 7 or 8 respectively, the time increases/ decreases rapidly and continuously from minutes to hours. Release 7 or 8 when you have reached the correct setting.

•If you need to adjust the time slowly, minute by minute, press 7 or 8 briefly and repeatedly.

3Press TIME, ALARM 1 or ALARM 2 to confirm your respective time setting.

SETTING THE DAY

Setting the day enables you to set the WEEKEND- SLEEPER function. If you attempt to use the WEEKEND-SLEEPERprior to setting the day (Monday

to Sunday, 1-7) will show briefly in the display to remind you to set the day first.

1Press SET DAY.

2While the day display is shown, press SET DAY again once or more to select the day numbered from dAY 1-7(Monday-Sunday):

™ The display will revert to show the clock time.

CD PLAYBACK

1To open the CD door, lift at the edge marked

LIFT TO OPEN.

2Insert a CD with the printed side facing up, and close the door.

3Press PLAY/ PAUSE 2; to start playback.

™ The CD indicator CD , Cd:--and the total number of tracks are shown, followed by the first track number before returning to clock time.

–door is shown if you have not closed the CD door/ open the CD door during playback.

–noCd is shown if no CD has been inserted/ inserted incorrectly.

–nFCd is shown if the CD-R(W) is non-finalized

–Err indicates a general error in operation of the set.

™The display returns to clock time.

4Adjust the sound with VOLUME $ or 3.

5To interrupt, press PLAY/ PAUSE 2;.

• The current track number shows briefly before returning to clock time. CD flashes during pause.

6Press PLAY/ PAUSE 2; again to resume playback.

7Press STOP 9 to stop playback.

™ The display returns to clock time.