Philips AX 2330 Programming track numbers Resume and Hold, Clearing the program, CD skips tracks

FEATURES	FEATURES / TROUBLESHOOTING
Programming track numbers	RESUME and HOLD

You can store up to 30 tracks to play in a program. A single track may be stored more than once in the program.

1 While playback is stopped, select a track with

∞or §.

2Press PROG to store the track.

y PROG lights up; the track number programmed and P with the total number of stored tracks are displayed.

3Select and store all desired tracks in this way.

4Press 2; to start playback of your selected tracks. y PROG is shown and playback starts.

• You can review the program by pressing PROG for more than 2 seconds.

y The display shows all the stored tracks in sequence.

Notes: – If you press PROG and there is no track select- ed, noProg is displayed.

–If you try to store more than 30 tracks, FULL is displayed.

Clearing the program

• While playback is stopped, press 9 to clear program. y CLEAr is displayed once, PROG goes off, and

the program is cleared.

Note: The program will also be cleared if the power supply is interrupted, or if the CD-player lid is opened, or if the set switches off automatically.

Selecting different playing possibilities-MODE

It is possible to play tracks in random order, to repeat a single track or the entire CD, and to play the first few seconds of each track.

1Press MODE during playback as often as required in order to activate one of the following ‘modes’. The active mode is shown in the display.

y SHUFFLE : All tracks of the CD are played in random order until all of them have been played once.

y SHUFFLE REPEAT ALL : All tracks of the CD are played repeatedly in random order.

y REPEAT : The current track is played repeatedly.

y REPEAT ALL : The entire CD is played repeatedly.

ySCAN: The first 10 seconds of each of the remaining tracks are played in sequence.

2Playback starts in the chosen mode after 2 seconds.

•To return to normal playback, press MODE repeatedly until the display shows no active modes.

ESP

With a conventional portable CD-player you might have experienced that the music stopped e.g. when you were jogging. The Electronic Skip Protection prevents loss of sound caused by light vibrations and shocks. Continuous playback is ensured. However ESP does not prevent playback interruptions during vigorous running. It also does not protect the unit against any damage caused by dropping!

In this set ESP is default ON. It is possible to set ESP off.

•Press MODE for more than 2 seconds. y ESP disappears.

•Press MODE again for more than 2 seconds. y ESP is displayed.

ESP on ➟ ESP off ➟ ESP on

You can interrupt playback and continue (after up to 1 minute in the disc stop position only) from the position where playback stopped (RESUME) You can lock all buttons of the set so that no action will be executed (HOLD). Use the RESUME–HOLD–OFF slider for these functions.

RESUME – continuing from where you have stopped

1 Switch the slider to RESUME during playback to acti- vate RESUME.

y RESUME is shown.

2 Press 9 whenever you want to stop playback.

3Press 2; whenever you want to resume playback. y RESUME is shown and playback continues from

where you have stopped.

•To deactivate RESUME, switch the slider to OFF. y RESUME goes off.

HOLD – locking all buttons

You can lock the buttons of the set by switching the slider to HOLD. Now, when a key is pressed, no action will be executed. This is of use, for example, when transporting the player in a bag. With HOLD activated, you can avoid accidental activation of other functions.

1Switch the slider to HOLD to activate HOLD.

y All buttons are locked. HoLd is shown when you press any button. If the set is switched off,

HOLD will be shown only when 2; is pressed.

2To deactivate HOLD, switch the slider to OFF.

Note: If you deactivate HOLD by switching the slider to RESUME, you will be activating the RESUME function.

Troubleshooting

WARNING: Under no circumstances should you try to repair the set yourself as this will invalidate the warranty. If a fault occurs, first check the points listed, before taking the unit for repair. If you are unable to solve a problem by following these hints, consult your dealer or service center.

The CD player has no power, or playback does not start

•Check that your batteries are not dead or empty, that they are inserted correctly, that the contact pins are clean.

•Your adapter connection may be loose. Connect it securely.

•For in-car use, check that the car ignition is on. Also check player’s batteries.

The indication no diSC is displayed

•Check that the CD is clean and correctly inserted (label-side upward).

•If your lens has steamed up, wait a few minutes for this to clear.

The indication nF diSC is displayed

• CD-RW (CD-R) was not recorded properly. Use FINALIZE on your CD-recorder.

The indication HOLD is on and/or there is no reaction to controls

•If HOLD is activated, then deactivate it.

•Electrostatic discharge. Disconnect power or remove batteries for a few seconds.

The CD skips tracks

•The CD is damaged or dirty. Replace or clean the CD.

•RESUME, SHUFFLE or PROGRAM is active. Switch off whichever is on.

No sound or bad sound quality.

•PAUSE might be active. Press 2;.

•Loose, wrong or dirty connections. Check and clean connections.

•Volume might not be appropriately adjusted. Adjust the volume.

•Strong magnetic fields. Check player’s position and connections. Also keep away from active mobile phones.

•For in-car use, check that the cassette adapter is inserted correctly, that the car cassette player’s playback direction is correct (press autoreverse to change), and that the cigarette lighter jack is clean. Allow time for temperature change.