Philips AZ1325 user manual Digital Tuner, CD Player

DIGITAL TUNER DIGITAL TUNER

CD PLAYER CD PLAYER

DIGITAL TUNER

Tuning to radio stations

1.Adjust the POWER slider to MW or FM.

™The radio. station frequency, waveband are shown (See 3)

2.Press and hold SEARCH ∞ or § until the frequency in the display starts running.

™The radio automatically tunes to a station of sufficient reception. Display shows Srch during automatic tuning.

3.Repeat step 2 if necessary until you find the desired station.

•To tune to a weak station, press ∞ or § briefly and repeatedly until you have found optimal reception.

To improve radio reception:

•For FM, extend, incline and turn the telescopic aer- ial. Reduce its length if the signal is too strong.

•For MW , the set uses a built-in aerial. Direct this aerial by turning the whole set.

Programming radio stations

You can store up to a total of 30 radio stations (20 FM and 10 MW) in the memory, manually or automatically (Autostore).

Manual programming

1.Tune to your desired station (see Tuning to radio stations).

2.Press PROG to activate programming.

™ PROG flashes.

3.Press PRESET + / - once or more to select a preset number.

•Remote control (AZ1325 models only): Press PRESET + / - once or more to select a preset

station.

4.Press PROG to confirm.

5.Repeat steps 1-4to store other stations.

Note : You can erase a preset station by storing another frequency in its place.

Autostore

Autostore automatically starts programming radio stations from preset 1. Available stations are programmed in order if the station with sufficient reception strength. Any previous presets e.g. manually programmed will be erased.

•Press PROG for 2 seconds or more to activate autostore programming.

™The display shows AUtO, PROG blinks, followed by the radio station details when stored.

After all stations are stored, the first preset station will then automatically play.

To listen to a preset station

•Press the PRESET + ,- buttons once or more until the desired preset station is displayed.

•Remote control (AZ1325 models only): optionally, press PRESET + ,- to select your preset station.

Playing a CD

This CD player plays Audio Discs including CD- Recordables and CD-Rewritables.

1.Adjust the POWER slider to CD.

2.Open the CD Door.

™OPEN is displayed.

3.Insert a CD with the printed side facing up and close the door.

™nocd if no CD inserted/ CD dirty, incorrectly inserted or damaged.

™nFcd if you have inserted a non-finalized CD- R(W).

4.Press 2; to start playback.

5.To pause playback press 2;. Press 2; again to resume play.

™Display: flashes during pause.

6.To stop CD playback, press the 9 button.

Note : CD play will also stop when:

-the CD door is opened

-the CD has reached the end

-you select MW / FM function.

Selecting a different track

•Press SEARCH ∞ or § once or repeatedly to select your track.

•In the pause / stop position, press.2; to start playback.

Finding a passage within a track

1.Press and hold SEARCH ∞ or §.

– The CD is played at high speed and low volume.

2.When you recognize the passage you want, release ∞ or § to resume normal playback.

Note : During a CD program or if SHUFFLE/ REPEAT active, searching is only possible within a

track.

Different play modes: SHUFFLE and REPEAT

You can select and change the various play modes before or during playback, and combine the modes with PROG. (See 4)

(SHUFFLE) - tracks of the entire CD/ program are played in random order

(SHUFFLE REPEAT ALL) - to repeat the entire CD/ program continuously in random order (REPEAT ALL) - repeats the entire CD/

program

(REPEAT) - plays the current track continuously

1.To select play mode, press MODE once or more.

2.Press 2; to start playback if in the stop position.

3.To select normal playback, press MODE repeatedly until the various modes are no longer displayed.

–You can also press the 9 button to cancel your play mode.