SETUPS

Network Connection

Set up the network connection settings in order to use the BD-Live function with a BD-Live disc.

Connection Test

 

“Advanced

“Network

 

“Connection

HOME A “Settings” A

Setup”

A“Others” A Connection”

A

Test”

After you made IP address/DNS settings or when a LAN cable is connected, always perform the connection test to check if the connection is correctly made.

1)Use [K / L] to highlight “Settings” in the home menu, then press [OK].

2)Use [K / L] to highlight “Advanced Setup”, then press [OK].

3)Use [K / L] to highlight “Others”, then press [OK].

4)Use [K / L] to highlight “Network Connection”, then press [OK].

5)Use [K / L] to highlight “Connection Test”, then press [OK].

Connection test will start automatically and the test result will appear right after the connection test finishes.

•“Testing...” : The test is in progress.

•“Pass” : Connection test is successfully completed.

•“Fail” : Connection test failed. Check the connection

settings.

Press [OK] to go to the list of network status confirmation screen.

IP Address

***.***.***.***

Subnet Mask

***.***.***.***

Default Gateway

***.***.***.***

Primary DNS

***.***.***.***

Secondary DNS

***.***.***.***

 

then press 'OK'.

 

 

 

 

6)Press [OK] to go back to the previous screen, or press [HOME ] to go back to the home menu.

Note

•If the connection test passes, you can enjoy the BD- Live functions using the Internet without making any extra settings.

•If the connection test fails, you may need to change the MAC address settings of your router. You can check the MAC address of this unit on “Network Status” screen. (refer to page 45).

Enable(Easy)

 

“Advanced

“Network

 

“Enable

HOME A“Settings” A

Setup”

A“Others” AConnection”

A

(Easy)”

Network settings are set to the following settings initially. (In most cases, you can connect to the Internet without making any changes to the default settings.)

- IP Address Setting

Auto(DHCP)

- DNS Setting

Auto(DHCP)

- Proxy Setting

Do Not Use

- Connection Speed

Auto

- BD-Live Setting

Allow

If you want to set the network settings back to the default settings as above (except “BD-Live Setting”), follow the procedure below.

1)Follow steps 1) to 4) in “Connection Test” on this page.

2)Use [K / L] to highlight “Enable(Easy)”, then press [OK].

•The unit will start the connection test automatically and the test result will appear right after the test finishes.

•After the connection test finishes, press [OK] to go to network status confirmation screen.

3)Press [OK] to activate the network settings and set

the network connection automatically. [HOME ] to go back to the home menu.

Note

•The setting of “BD-Live Setting” will not be set back to the default, even if you follow the procedure.

Enable(Custom)

 

“Advanced

“Network

“Enable

HOME A“Settings” A

Setup”

A“Others” AConnection”

A(Custom)”

In following cases, select “Enable(Custom)” to set each setting as necessary.

-When connection test failed with the setting of “Enable(Easy)”.

-When instructed by your Internet service provider to make specific settings in accordance with your network environment.

•IP Address Setting / DNS Setting

1)Follow steps 1) to 4) in “Connection Test” on this page.

2)Use [K / L] to highlight “Enable(Custom)”, then press [OK].

3)Use [K / L] to highlight “IP Address Setting”, then press [OK].

4)Use [K / L] to highlight the desired setting, then press [OK].

“Auto(DHCP)”

: If your router has DHCP server

 

function, select “Auto(DHCP)”.

“Manual”

: If your router does not have DHCP

 

server function, select “Manual”.

 

 

Others Setup Function PlaybackSetup Basic Connections Introduction

EN 43