english
Introduction
The Philips Shaving Head Cleaner thoroughly cleans the shaving heads of your shaver for a good shaving result.
This product used to be called Action Clean.
Preparing the Philips Shaving Head Cleaner for use
The Philips Shaving Head Cleaner can be used to clean shavers with two and three shaving heads.
1Turn the top of the Philips Shaving Head Cleaner anticlockwise (1) and pull it from the base (2). (Fig. 1)
2Remove the filter unit from the base. (Fig. 2)
3Place the appropriate shaving unit holder onto the filter unit.The appropriate shaving units for the different shaver series are shown in the pictures below.
,Suitable for Sensotec shavers (HQ8000 series). (Fig. 3)
,Suitable for Quadra shavers (HQ7000/6000 series). (Fig. 4)
,Suitable for all other
,Suitable for Quadra Action shavers (HQ600 series). (Fig. 6)
,Suitable for all other
4Make sure the lugs on the holder fit into the slots of the filter unit.
(Fig. 8)
5Empty the contents of the bottle of cleaning fluid into the base.
(Fig. 9)
Be careful not to spill cleaning fluid onto polished surfaces, such as bathroom worktops, as they may become blotched and dull as a result.
Using the Philips Shaving Head Cleaner
Clean the shaving unit with the Philips Shaving Head Cleaner once a month.
1Fit the shaving unit onto the holder. (Fig. 10)
HQ8000 series only:
,Slide the spring of the HQ8000 shaving unit into the recess of the
shaving unit holder. (Fig. 11)
Make sure the spring remains properly in place in the recess when you close the shaving unit.
,Close the shaving unit by pushing it carefully down onto the holder. (Fig. 12)
2Place the top of the Philips Shaving Head Cleaner on the base (1) and turn it clockwise until you hear a click (2). (Fig. 13)
3Pump the cleaning fluid through the shaving unit by pushing the top of the Philips Shaving Head Cleaner down 30 times. (Fig. 14)
4When you are finished, remove the top from the base and remove the shaving unit from the holder. (Fig. 15)
Place the shaving unit on a piece of kitchen towel or tissue and allow it to dry.
5Do not rinse the shaving unit with water. (Fig. 16)
Note:The Sensotec (HQ8000 series), Quadra (HQ7000/6000 series) and Quadra Action (HQ600 series) shavers are watertight and can be cleaned under the tap.
Be careful with hot water.Always check if the water is not too hot to prevent your hands from getting burnt.
6Place the top of the Philips Shaving Head Cleaner on the base (1) and turn it clockwise until you hear a click (2). (Fig. 13)
,You can clean the shaving unit every month with the same cleaning fluid for a whole year.
Replacing the filter and the cleaning fluid
Only use Philips Shaving Head Cleaning Fluid HQ101, which includes a bottle of cleaning fluid and a filter.The Philips Shaving Head Cleaning Fluid HQ101 can be obtained from your Philips dealer.
1Remove the filter unit. (Fig. 17)
2Remove the old filter from the filter unit. (Fig. 18)
3Place a new filter in the filter unit. (Fig. 19)
4Pour the used cleaning fluid into a bottle (for more information on disposal of the fluid, see chapter ‘Environment’). (Fig. 20)
5Place the filter unit in the base. (Fig. 21)
6Fill the base of the Philips Shaving Head Cleaner with new cleaning fluid. (Fig. 22)
Environment
,Do not pour old cleaning fluid down the sink, but pour it in a bottle and hand it in at an official collection point for chemical waste. By doing this you will help to preserve the environment. (Fig. 23)
422200182547 | 2/8 |
