Philips HTS3051BV/F7, HTS3051BV/F8 EasyLink (HDMI CEC), Network Connection, Standby, One Touch Play, Connection Test, System Information

SETUPS

EasyLink (HDMI CEC)

home A “Settings” A	“Advanced	A “Others” A	“EasyLink
	Setup”		(HDMI CEC)”

This unit supports Philips EasyLink, which enables your TV (limited to PHILIPS brand EasyLink TV) to act in conjunction with this unit, or vice versa. Compliant TV must be connected to the HDMI OUT jack.

When “EasyLink (HDMI CEC)” setting is set to “On”, functions listed below will be available.

One Touch Play

When the operations with following buttons of the remote control of this unit are performed, the TV will automatically be turned on and switched to the appropriate input channel.

Buttons for one touch play:

-[B (play)], [S(previous)], [T(next)],

[the Number buttons], [ (home)], [INFO ], or

[SOURCE]

-[TOP MENU], or [DISC MENU / POP-UP MENU] (when a disc is inserted in the unit)

Standby

When you press and hold [Q(standby/on)] for 2 seconds, it turns off the power of the TV first and then turns off the power of this unit also.

System Information

Get & Set Menu Language

The unit recognizes the OSD language set for the TV and automatically sets the same language as the player menu language (OSD menu language) for this unit. Refer to the “Player Menu” on page 39 for available languages.

•This feature is available only when “Auto” is selected in the “Player Menu” in the settings menu.

Note

•For external input mode, “One Touch Play” is not available.

Network Connection EN

Set up network connection settings in order to use

BD-Live, VUDU or network upgrade function.

Connection Test

	home A “Settings” A“Advanced		A“Others” A “Network A		“Connection
		Setup”		Connection”	Test”
After you made IP address / DNS settings or when a LAN
cable is connected, always perform the connection test to
check if the connection is correctly made.
1) Use [K / L] to select “Settings” in the home menu,
						Introduction
3) Use [K / L] to select “Others”, then press [OK].
	then press [OK].
2) Use [K / L] to select “Advanced Setup”, then press
	[OK].
4) Use [K / L] to select “Network Connection”, then
	press [OK].
						Connections
	• “Testing...” : The test is in progress.
5) Use [K / L] to select “Connection Test”, then press
	[OK].
Connection test will start automatically and the test result
will appear right after the connection test finishes.
	• “Pass” : Connection test is successfully completed.
	• “Fail” : Connection test failed. Check the connection
		settings.				Basic
Press [OK] to go to the list of network status confirmation
screen.						Setup
		IP Address		xxx.xxx.xxx.xxx
		Subnet Mask		xxx.xxx.xxx.xxx
		Default Gateway		xxx.xxx.xxx.xxx
		Primary DNS		xxx.xxx.xxx.xxx
		Secondary DNS		xxx.xxx.xxx.xxx		Playback
				then press 'OK'.
6) Press [OK] to go back to the previous screen, or
	press [ (home)] to go back to the home menu.
	Note					Function
	• If the connection test passes, you are ready to use
	BD-Live, VUDU or network upgrade function using
	the Internet without making any additional settings.					Setup
	• If the connection test fails, you may need to change
	the MAC address settings on your router. You can
	check the MAC address of this unit on “Network
	Status” screen (refer to page 52).
	• When connecting this unit directly to a modem for
	the first time or connecting it to a modem which was					Others
	previously connected to any other network
	device(e.g. a router, PC, etc.), you may have to
	power cycle the modem to reset the settings on the
	modem.

EN 49