Philips Protected Metal Halide “O” Rated Lamps
Ordering Data
|
|
|
|
|
|
|
| Rated |
|
|
|
|
Product |
| Nom. | ANSI | Bulb | Bulb | MOL | LCL | Avg.Life | Initial | Mean |
|
|
Number | OrderingCode | Watts | Code | Size | Finish | (In.) | (In.) | (Hrs.)1 | Lumens | Lumens | CRI | CCT |
MP175/BU | 175 | M57/O | CLEAR | 8 5⁄16 | 5 | 10,000 | 15,000 | 12,000 | 65 | 3800K | ||
MP250/BU | 250 | M58/O | CLEAR | 8 5⁄16 | 5 | 10,000 | 22,000 | 16,500 | 62 | 3800K | ||
MP360/BU/EW | 360 | M165/M59/O | CLEAR | 11 1⁄2 | 7 | 20,000 | 34,200 | 23,940 | 65 | 4000K | ||
MP360/C/BU/EW | 360 | M165/M59/O | COATED | 11 1⁄2 | — | 20,000 | 31,700 | 20,605 | 68 | 3600K | ||
MP400/BU | 400 | M59/O | CLEAR | 11 1⁄2 | 7 | 20,000 | 38,000 | 26,600 | 65 | 4000K | ||
MP400/C/BU | 400 | M59/O | COATED | 11 1⁄2 | — | 20,000 | 34,500 | 22,425 | 67 | 3700K | ||
MP1000/BU | 1000 | M47/O | CLEAR | 15 3⁄8 | 9.5 | 12,000 | 107,000 | 75,000 | 65 | 3900K |
Nickel plated brass base
1)Rated average life is the life obtained, on the average, from large representative groups of lamps in laboratory tests under controlled conditions at 10 or more operating hours per start. It is based on survival of at least 50% of the lamps and allows for individual lamps or groups of lamps to vary considerably from the average. For lamps with a rated average life of 24,000 hours, life is based on survival of 67% of the lamps.
2)Approximate lumen values listed are for vertical operation of the lamp.
3)Approximate lumen output at 40% of lamp rated average life.
Above specifications subject to change without notice.
Electrical andTechnical Data
RMS Lamp Operating Current (Amps) Nominal
Physical Characteristics
Bulb Temperature (Maximum)
Standard Package Quantity
Protected Metal Halide Lamps, Open or Enclosed Fixtures, Base Up Operation,
± 15º Unless Otherwise Noted
Recommended Warnings, Cautions and Operating Instructions
R“WARNING: These lamps can cause serious skin burn and eye inflammation from shortwave ultraviolet radiation if outer envelope of the lamp is broken or punctured. Do not use where
people will remain for more than a few minutes unless adequate shielding or other safety precautions are used.Certain lamps that will automatically extinguish when the outer envelope is broken or punctured are commercially available.”This lamp complies with FDA radiation performance standard 21 CFR subchapterJ. (USA:21CFR
If the outer bulb is broken or punctured, turn off at once and replace the lamp to avoid possible injury from hazardous short wave ultraviolet radiation. Do not scratch the outer bulb or subject it to pressure as this could cause the outer bulb to crack or shatter.A partial vacuum in the outer bulb may cause glass to fly if the envelope is struck.
WARNING:The
INJURY,PROPERTY DAMAGE,BURNSAND FIRE.
These lamps are designed to retain all the glass particles should an arc tube rupture occur.The following operating instructions are recommended to minimize these occurrences.
RELAMP FIXTURESAT OR BEFORETHE END OF RATED LIFE.Allowing lamps to operate until they fail is not advised and may increase the possibility of inner arc tube rupture.
CAUTION:TO REDUCETHE RISK OF PERSONAL INJURY,PROPERTY DAMAGE, BURNS AND FIRE RESULTING FROM AN
LAMP OPERATING INSTRUCTIONS:
1.RELAMP FIXTURESATOR BEFORETHE END OF RATED LIFE.Allowing lamps to operate until they fail is not advised and may increasethe possibility of inner arc tube rupture.
2.Before lamp installation/replacement, shut power off and allow lamp and fixture to cool to avoid electrical shock and potential burn hazards.
3.Use only auxiliary equipment meeting Philips and/or ANSI standards. Use within voltage limits recommended by ballast manufacturer.
A.Operate lamp only within specified limits of operation.
B.For total supply load refer to ballast manufacturers electrical data.
4.Periodically inspect the outer envelope. Replace any lamps that show scratches,cracks or damage.
5.If a lamp bulb support is used, be sure to insulate the support electrically to avoid possible decomposition of the bulb glass.
6.Protect lamp base, socket and wiring against moisture,corrosive atmospheres and excessive heat.
7.Time should be allowed for lamps to stabilize in color when turned on for the first time. This may require several hours of operation, with more than one start. Lamp color is also subject to change under conditions of excess vibration or shock, and color appearance may vary between individual lamps.
8.Lamps may require 10 to 20 minutes to
9.Take care in handling and disposing of lamps. If an arc tube is broken, avoid skin contact with any of the contents or fragments.
10.Do not use this lamp:
A.In a fixture that contains a Pulse Start metal halide ballast.
B.In a fixture that is specifically designed for use with Pulse Start metal halide lamps.
Operation of these lamps on Pulse Start Metal Halide systems may increase the chance of an outer bulb rupture and pieces of extremely hot glass might be discharged into the surrounding environment. If such a rupture were to happen,THERE ISA RISK OF PERSONAL INJURY,PROPERTY DAMAGE, BURNSAND FIRE.
About Metal Halide Lamp Classifications
Every metal halide lamp is classified under one of the following three American National Standards Institute (ANSI) classifications:
For more information on “Best Practices for Metal Halide Lighting Systems,”please visit www.nema.org and search for document number LSD
©2007 Philips Lighting Company. All rights reserved. Printed in USA 06/07
www. philips.com
Philips Lighting Company | Philips Lighting |
200 Franklin Square Drive | 281 Hillmount Road |
P.O. Box 6800 | Markham, Ontario |
Somerset, NJ | Canada L6C 2S3 |
A Division of Philips Electronics North America Corporation | A Division of Philips Electronics Ltd. |
Printed on chlorine free paper from Sappi Fine Paper mills, who are accredited with EMAS environmental certification. Sappi claims that the pulp used in the manufacture of Magno Dull paper is derived from environmentally certified forests.
