Philips SA1210, AZT3202, AZT3200 warranty Features

FEATURES

Programming track numbers

You can store up to 30 tracks to play in a program. A single track may be stored more than once in the program.

1 While playback is stopped, select a track with ∞ or §.

2Press PROG to store the track.

yprogram lights up; the track number

programmed and P with the total number of stored tracks are displayed.

3Select and store all desired tracks in this way.

4Press 2; to start playback of your selected tracks.

yprogram is shown and playback starts.

•You can review the program by pressing PROG for more than 2 seconds.

yThe display shows all the stored tracks in sequence.

Notes: – If you press PROG and there is no track selected, SEL is displayed.

– If you try to store more than 30 tracks, FULL is displayed.

Clearing the program

•While playback is stopped, press 9 to clear program. yCLR is displayed once, program goes off,

and the program is cleared.

Note: The program will also be cleared if the power supply is interrupted, or if the CD-player lid is opened, or if the set switches off automatically.

Selecting different playing possibilities−MODE

It is possible to play tracks in random order, to repeat a

single track or the entire CD, and to play the first few

seconds of each track.

1 Press MODE during playback as often as required in order to activate one of the following ‘modes’. The

active mode is shown in the display. yshuffle : All tracks of the CD are played in

random order until all of them have been played once.

yshuffle repeat all : All tracks of the CD are played repeatedly in random order.

yrepeat : The current track is played repeatedly.

yrepeat all : The entire CD is played repeatedly.

ySCAN: The first 10 seconds of each of the remain- ing tracks are played in sequence.

2Playback starts in the chosen mode after 2 seconds.

•To return to normal playback, press MODE repeatedly until the display shows no active modes.

ESP / Power Save Mode

With a conventional portable CD-player you might have experienced that the music stopped e.g. when you were jogging. The ELECTRONIC SKIP PROTECTION prevents loss of sound caused by light vibrations and shocks. Continuous playback is ensured. However ESP does not prevent playback interruptions during vigorous running. It also does not protect the unit against any damage caused by dropping! On this set ESP is default on. It is possible to set ESP off and enter the Power Save mode. The Power Save mode helps to extend battery

lifetime for longer playback.

•Press MODE for more than 2 seconds.

y disappears. power save modeis now activated.

•Press MODE again for more than 2 seconds. y is displayed once

FEATURES

RESUME and HOLD

You can interrupt playback and continue (even after an extended period of time) from the position where playback stopped (RESUME) and you can lock all buttons of the set so that no action will be executed (HOLD). Use the RESUME–HOLD–OFF slider for these functions.

RESUME – continuing from where you have stopped

1Switch the slider to RESUME during playback to activate RESUME. yresume is shown.

2Press 9 whenever you want to stop playback.

3 Press 2; whenever you want to resume playback. yresume is shown and playback continues

from where you have stopped.

•To deactivate RESUME, switch the slider to OFF. yresume goes off.

HOLD – locking all buttons

You can lock the buttons of the set by switching the slider to HOLD. Now, when a key is pressed, no action will be executed. This is of use, for example, when transporting the player in a bag. With HOLD activated, you can avoid accidental activation of other functions.

1Switch the slider to HOLD to activate HOLD. yAll buttons are locked. HoLd is shown when

you press any button. If the set is switched off, hold will be shown only when 2; or FM is pressed.

2To deactivate HOLD, switch the slider to OFF.

Note: If you deactivate HOLD by switching the slider to RESUME, you will be activating the RESUME function.

Radio Play

You can tune to any FM station automatically or manually.

1 Press FM to switch the radio on.

Tuning to radio stations automatically

1Keep ∞ or § pressed for at least 2 second.

yThe radio tunes to a station with sufficient strength and radio play starts. The current waveband and frequency are displayed.

2Repeat searching until you find the desired radio station.

Tuning to radio stations manually

1Keep ∞ or § pressed.

2Release ∞ or §, then briefly press ∞ or § again when you are close to the desired frequency.

3Briefly press ∞ or § repeatedly until you reach the desired frequency.

yRadio play starts. The current waveband and frequency are displayed.

•To switch from radio play to CD play, press 2; .

•Press FM or 9 to switch the radio off.