1060 1070

6.5” Midrange Extended Drivers

 

 

1060

1070

 

 

TYPICAL CHARACTERISTICS

 

 

 

 

 

 

Rated impedance

Z

8

 

16

 

Reference efficiency (1 W@1 m)

-

97

 

97

 

dB SPL

Usable frequency range 1

-

300–6000

300–6000

 

Hz

Power handling capacity 2 (AES)

-

130

 

130

 

W

Max Sound Pressure Level 3

SPLmax

114

 

114

 

dB SPL

Min. impedance modulus

Zmin

6.0 @ 640Hz 12.9 @ 640Hz

Voice-coil inductance 4 @ 1 kHz

Le1k

0.58

 

1.22

 

mH

@ 10 kHz

Le10k

0.23

 

0.48

 

mH

Bl product

Bl

8.5

 

11.2

 

N/A

Moving mass

Mms

0.0085

 

0.0085

 

Kg

THIELE-SMALL PARAMETERS : TYPICAL (QC LIMITS)

 

 

 

 

 

Resonance frequency 5

Fs

130 (±25)

130 (±25)

 

Hz

DC resistance 6

Re

5.4 (±0.5)

11.6 (±1.1)

 

Mechanical quality factor

Qms

6.6

 

6.6

 

1

Electrical quality factor

Qes

0.52

 

0.50

 

1

Total quality factor

Qts

0.48

 

0.46

 

1

Mechanical suspension compliance

Cms

180

 

180

10-6m/N

Effective piston area

S

0.0150

 

0.0150

 

m2

 

d

 

 

 

 

 

Equivalent Cas air load

Vas

0.0056

 

0.0056

 

m3

Max. linear excursion

Xmax

±2.0

 

±2.0

 

mm

Linear displacement volume

Vd

0.030

 

0.030

 

10-3 m3

Half-space efficiency

 

2.3

 

2.3

 

%

Unity load volume

Vas Qts2

1.3

 

1.2

 

10-3 m3

ABSOLUTE MAXIMUM RATINGS

 

 

 

 

 

 

Short term max. input voltage 7

Vmax

65

 

90

 

V

Max. excursion before damage

Xdam

4.0

 

4.0

 

mm

Ambient operating temperature

 

–10

to

+50

 

°C

Storage temperature 8

 

–20

to

+70

 

°C

Environmental conditions 9

 

Outdoor

 

 

APPLICATION INFORMATION

 

 

 

 

 

 

Air volume occupied by the driver 10

 

0.46

 

0.46

 

10-3 m3

Speaker net mass

 

2.15

 

2.15

 

Kg

Recommended reflex box

Vb/Fb

3L / sealed

 

L / Hz

Electrical polarity

A positive voltage applied on the red

 

 

 

terminal produces forward cone motion.

PHYSICAL CHARACTERISTICS

187.5max.

(onangles)

4 x Ø 5.3 Holes on Ø 172

 

Ø

 

 

+ Red dot

 

NO

 

 

FAST

 

 

8.0 x35 .6

inalerm T

 

 

 

Ø 162.5 max.

8

 

 

68.5 max.

 

 

 

 

Ø 117.5 max.

 

 

Ø 145.3 max.

SPECIFICATION NOTES

Note 1 : Allowing for energy response, excursion capability, Power spectrum, and -3dB low freq. roll-off for standard reflex tuning.

Note 2 : Established at 20°C ambient temp, according to AES2-1984 standard using IEC268-1 simulated programme signal and a 3 liter sealed test enclosure with a 2nd order high-pass filter @ 400Hz.

Note 3 : Established at 1m on axis of the loudspeaker mounted

in test enclosure, when driven at full AES Power Handling Capacity, including 4dB of thermal compression loss.

Note 4 : Measured at 20 mA in free air.

Note 5 : Measured at 20 mA and 20°C ambient temp. in free air conditions, after full run and rest.

Note 6 : Measured at 20°C ambient temp.

QC limits are ±10 %

Note 7 : Stated in RMS voltage according to IEC 268-5.

Note 8 : Includes shipping conditions. The lower limit prevents from demagnetization.

Note 9: Our products are classified in three categories : Indoor, Outdoor, and Outdoorfor permanent outdoor use or severe conditions.

Note 10 : Calculated for front mounting on to a 18 mm thick board.

461, rue des chênes Z.A 77590 CHARTRETTES FRANCE

Tél : 33 01 64 81 29 80

Fax : 33 01 60 69 10 28

e-mail : phlaudio@phlaudio.com

http: //www.phlaudio.com

PHL Audio S.A. provides these specifications as representative of current production after conditioning. Because of our continuous research, they are subject to change without notice.

Page 2
Image 2
PHL Audio E17 specifications 1060 1070, 162.5 max, max 117.5 max 145.3 max