SPECIFICATIONS
SD1300.1 SPECIFICATIONS
Amplifier Owner’s Manual
Frequency Response: Signal to Noise Ratio: Low Pass Crossover:
Subsonic Filter:
Low Pass Crossover Range: Subsonic Crossover Range: Bass Boost @ 45Hz:
Low Level Input Range: Lowest Recommend Load: Typical Efficiency: Damping Factor:
±1dB from 20Hz to 300Hz >90dB
18dB per Octave 12dB per Octave 30Hz to 300Hz 10Hz to 55Hz
0 to +18dB
200 millivolts to 8 volts
1 ohm
70%
Greater than 200
RMS Power 14.4Vdc ≤ 1% THD | 900 x 1 @ 2 ohms | |
| 1300 x 1 | @ 1 ohm |
Dynamic Power 14.4Vdc >1% THD | 1200 x 1 | @ 2 ohms |
| 1600 x 1 | @ 1 ohm |
Recommended Fuse Size: | 120 amp | |
Power/Ground Wire Size: | 4 Gauge |
|
Dimensions (Includes Mounting Feet): | 14.33” L x 6.93”W x 2.0” H | |
| 364mm L x 176mm W x 51mm H | |
Dimensions (Includes Terminals): | 14.96” L x 6.93”W x 2.0” H | |
| 380mm L x 176mm W x 51mm H | |
SD1300.5 SPECIFICATIONS
Frequency Response: | ± 1dB from 20Hz to 20kHz |
Signal to Noise Ratio: | >100dB |
High Pass Crossovers: | 12dB per Octave |
Low Pass Crossover: | 18dB per Octave |
High Pass Crossover Range: | 15Hz to 250Hz |
Low Pass Crossover Range: | 30Hz to 300Hz |
Bass Boost @ 45Hz: | 0 to +18dB |
Low Level Input Range: | 200 millivolts to 8 volts |
Front and Rear Channels Lowest Load: | 4 ohms Bridged or 2 ohms Stereo |
Subwoofer Channel Lowest Load: | 2 ohm |
Typical Efficiency: | 70% |
Damping Factor | Greater than 200 |
Note: All SD amplifiers operate correctly up to 14.4 volts. Do not operate the amplifier above 14.4 volts. The amplifier will engage its overvoltage protection, the result is no audio output on one or more channels.
RMS Power 14.4Vdc ≤1% THD | 80 x 4 @ 4 ohms Stereo | ||
| 125 x 4 @ | 2 ohms Stereo | |
| 250 x 2 @ | 4 ohms Bridged | |
| plus |
| |
| 500 x 1 @ | 4 ohms | |
| 800 x 1 | @ | 2 ohms |
Dynamic Power 14.4Vdc >1% THD | 95 x 4 @ 4 ohms Stereo | ||
| 150 x 4 | @ | 2 ohms Stereo |
| 300 x 2 | @ | 4 ohms Bridged |
| plus |
| |
| 700 x 1 | @ | 4 ohms |
| 1000 x 1 @ 2 ohms | ||
Recommended Fuse Size: | 100 amp |
| |
Power/Ground Wire Size: | 4 Gauge |
| |
Dimensions (Includes Mounting Feet): | 14.33” L x 6.93”W x 2.0” H | ||
| 364mm L x 176mm W x 51mm H | ||
Dimensions (Includes Terminals): | 14.96” L x 6.93”W x 2.0” H | ||
| 380mm L x 176mm W x 51mm H | ||
© 2011 Phoenix Gold • www.phoenixgold.com
