Amplifier Owner’s Manual
SPECIFICATIONS
Ti2 1000.4 SPECIFICATIONS
Frequency Response: | ± 1dB from 20Hz to 20kHz | RMS Power Output | 150w x 4 @ 4 ohms Stereo |
Signal to Noise Ratio: | >100dB |
| 250w x 4 @ 2 ohms Stereo |
Crossover Slopes: | 12dB per Octave |
| 500w x 2 @ 4 ohms Bridged |
Front High/Low Pass Crossover Range: | 45Hz to 4kHz |
|
|
Rear High Pass Crossover Range: | 20Hz to 4kHz | Power/Ground Wire Size: | 4 Gauge |
Rear Low Pass Crossover Range: | 40Hz to 4kHz | Recommend Power Wire Fuse: | 80a |
Low Level Input Range: | 200 millivolts to 8 volts | Dimensions: | 11.7” L x 7.1”W x 2.0” H |
Lowest Recommend Load: | 4 ohms Bridged/2 ohms Stereo |
| 296mm L x 180mm W x 52mm H |
Typical Efficiency: | 80% |
|
|
Damping Factor | Greater than 200 |
|
|
Ti2 1600.5 SPECIFICATIONS
FRONT AND REAR CHANNELS: |
|
Frequency Response: | ± 1dB from 20Hz to 20kHz |
Signal to Noise Ratio: | >100dB |
Crossover Slopes: | 12dB per Octave |
Front High Pass Crossover Range: | 20Hz to 4kHz |
Rear High Pass Crossover Range: | 20Hz to 4kHz |
Rear Low Pass Crossover Range: | 40Hz to 4kHz |
Low Level Input Range: | 200 millivolts to 8 volts |
Lowest Recommend Load: | 4 ohms Bridged/2 ohms Stereo |
Typical Efficiency: | 80% |
Damping Factor | Greater than 200 |
SUBWOOFER CHANNEL: |
|
Frequency Response: | ± 1dB from 20Hz to 300Hz |
Signal to Noise Ratio: | >100dB |
Crossover Slopes: | 12dB per Octave |
Low Pass Crossover Range: | 20Hz to 300Hz |
Subsonic Crossover Range: | 10Hz to 50Hz |
Variable Phase: | 0 to 180 degrees |
Low Level Input Range: | 200 millivolts to 8 volts |
Lowest Recommend Load: | 2 ohms |
Typical Efficiency: | 80% |
Damping Factor: | Greater than 200 |
RMS Power Output | 125w x 4 | @ 4 ohms Stereo |
| 200w x 4 | @ 2 ohms Stereo |
| 400w x 2 | @ 4 ohms Bridged |
RMS Power Output | 500w x 1 @ 4 ohms |
| 800w x 1 @ 2 ohms |
Recommend Power Wire Fuse: | 100a |
Power/Ground Wire Size: | 4 Gauge |
Dimensions: | 14.4” L x 7.1”W x 2.0” H |
| 366mm L x 180mm W x 52mm H |
POWER OUTPUT NOTE: A power birth certificate is included for each amplifier. Ti2 amplifiers are conservatively rated and will exceed their RMS power rating shown here. All RMS power ratings and measurements are at 14.4 volts with no more than 1% THD. Ti2 1000.4 and Ti2 1600.5 feature ADAPT technology which provides the same power output from 11 to 15 volts with music material.
www.phoenixgold.com
