This product conforms to new cord colors. Los colores de los cables de este producto se conforman con un nuevo código de colores.
As cores dos fios deste produto seguem um novo padrão de cores.
Æ…b¹b'« „öÝô« Ê«u
Printed in China |
|
<KMMNX> <03G00000> |
|
|
| 5 |
MANUEL |
| 60° | 6 |
|
| ||
| Fig. 1 | Fig. 3 | |
| ± qJA | ≥ qJA | |
D’INSTALLATION |
| ||
| 2 | 7 | |
1 |
| ||
|
| ||
| 182 |
| |
53 | 3 |
| |
|
| ||
| 4 |
| |
| Fig. 2 | Fig. 4 | |
| ≤ qJA | ¥ qJA |
8 | 11 |
| |
9 | 13 |
| 12 |
Fig. 5 | Fig. 7 |
µ qJA | ∑ qJA |
10 |
|
Fig. 6 |
|
∂ qJA |
|
Installation
Note:
•Before finally installing the unit, connect the wiring temporarily, making sure it is all connect- ed up properly, and the unit and the system work properly.
•Use only the parts included with the unit to ensure proper installation. The use of unautho- rized parts can cause malfunctions.
•Consult with your nearest dealer if installation requires the drilling of holes or other modifica- tions of the vehicle.
•Install the unit where it does not get in the dri- ver’s way and cannot injure the passenger if there is a sudden stop, like an emergency stop.
•The semiconductor laser will be damaged if it overheats, so don’t install the unit anywhere hot
— for instance, near a heater outlet.
•If installation angle exceeds 60° from horizontal, the unit might not give its optimum performance. (Fig 1)
•When installing, to ensure proper heat dispersal when using this unit, make sure you leave ample space behind the rear panel and wrap any loose cables so they are not blocking the vents.
DIN Front/Rear-mount
This unit can be properly installed either from “Front” (conventional DIN
DIN Front-mount
Installation with the rubber bush (Fig. 2)
1.Dashboard
2.Holder
After inserting the holder into the dashboard, then select the appropriate tabs according to the thickness of the dashboard material and bend them.
(Install as firmly as possible using the top and bottom tabs. To secure, bend the tabs 90 degrees.)
3.Rubber bush
4.Screw
<ENGLISH>
Removing the Unit (Fig. 3) (Fig. 4)
5.Frame
6.Insert the release pin into the hole in the bottom of the frame and pull out to remove the frame. (When reattaching the frame, point the side with a groove downwards and attach it.)
7.Insert the supplied extraction keys into the unit, as shown in the figure, until they click into place. Keeping the keys pressed against the sides of the unit, pull the unit out.
DIN Rear-mount
Installation using the screw holes on the side of the unit (Fig. 5) (Fig. 6) (Fig. 7)
1. Remove the frame.
8.Frame
9.Insert the release pin into the hole in the bottom of the frame and pull out to remove the frame. (When reattaching the frame, point the side with a groove downwards and attach it.)
2. Fastening the unit to the factory radio mounting bracket.
10.Select a position where the screw holes of the bracket and the screw holes of the head unit become aligned (are fitted), and tighten the
screws at 2 places on each side. Use either truss screws (5 × 8 mm) or flush surface screws
(5 × 9 mm), depending on the shape of the screw holes in the bracket.
11.Screw
12.Factory radio mounting bracket
13.Dashboard or Console