Operating this unit
| Section |
Operating this unit | 02 |
Selecting a source
1Press SRC/OFF to cycle between:
TUNER
Adjusting the volume
1Turn M.C. to adjust the volume.
CAUTION
For safety reasons, park your vehicle when removing the front panel.
Note
When this unit’s blue/white lead is connected to the vehicle’s
WARNING
!Keep the battery out of the reach of children. Should the battery be swallowed, consult a doctor immediately.
!Batteries (battery pack or batteries installed) must not be exposed to excessive heat such as sunshine, fire or the like.
CAUTION
! Use one CR2025 (3 V) lithium battery. |
! Remove the battery if the remote control is |
not used for a month or longer. |
! There is a danger of explosion if the battery is |
incorrectly replaced. Replace only with the |
same or equivalent type. |
! Do not handle the battery with metallic tools. |
! Do not store the battery with metallic ob- |
jects. |
! If the battery leaks, wipe the remote control |
Menu operations identical |
|
|
|
|
|
| Manual tuning (step by step) |
|
| ||
for set up menu/function |
| 1 | Press c or d. |
| English |
settings/audio adjustments/ |
| ! | If PCH (preset channel) is selected in SEEK, |
| |
|
| you cannot tune up or down manually. You |
| ||
initial settings/lists |
|
| need to select MAN (manual tuning) in SEEK. |
|
|
|
|
| For details about the settings, refer to SEEK |
|
|
Returning to the previous display |
|
|
|
| |
Returning to the previous list (the folder one level |
|
|
|
|
|
| Seeking |
|
| ||
higher) |
|
|
| ||
| 1 | Press and hold c or d, and then release. |
|
| |
1 Press . |
|
|
| ||
|
| You can cancel seek tuning by briefly pressing |
|
| |
|
|
|
|
| |
Returning to the ordinary display |
|
|
|
| |
|
| c or d. |
|
| |
Canceling the initial setting menu/set up menu |
|
| While pressing and holding c or d, you can |
|
|
1 Press BAND/ . |
|
| skip stations. Seek tuning starts as soon as |
|
|
Returning to the ordinary display from the list |
|
| you release c or d. |
|
|
|
|
|
|
| |
1 Press BAND/ . |
|
|
|
|
|
|
| Storing and recalling stations |
|
| |
|
|
| |||
Tuner |
| for each band |
|
| |
|
|
|
|
|
Using preset tuning buttons
Use and care of the remote control
Using the remote control
1Point the remote control in the direction of the front panel to operate.
When using for the first time, pull out the film protruding from the tray.
Replacing the battery
1Slide the tray out on the back of the remote control.
2Insert the battery with the plus (+) and minus
completely clean and install a new battery. |
! When disposing of used batteries, comply |
with governmental regulations or environ- |
mental public institutions’ rules that apply in |
your country/area. |
! “Perchlorate Material – special handling may |
apply. |
See www.dtsc.ca.gov/hazardouswaste/ |
perchlorate. (Applicable to California, |
U.S.A.)” |
Important
!Do not store the remote control in high tem- peratures or direct sunlight.
!The remote control may not function properly in direct sunlight.
!Do not let the remote control fall onto the floor, where it may become jammed under the brake or accelerator pedal.
Basic operations
Selecting a band
1Press BAND/ until the desired band (F1, F2, F3 for FM or AM) is displayed.
Recalling preset stations
1Press c or d.
!If MAN (manual tuning) is selected in SEEK, you cannot recall preset stations. You need to select PCH (preset channel) in SEEK. For de- tails about the settings, refer to SEEK (left/right key setting) on the next page.
1When you find a station that you want to store in memory, press one of the preset tuning buttons (1 to 6) and hold until the preset number stops flashing.
2Press one of the preset tuning buttons (1 to 6) to select the desired station.
Switching the display
Selecting the desired text information
1Press .
Program service
artist
!Depending on the band, text information can be changed.
!Text information items that can be changed depend on the area.
Function settings
1 Press M.C. to display the main menu.
En 5