Pioneer DEH-4400BT manual 18

Section
02		Operating this unit
	Initial settings
			Activate this setting when using an auxiliary device
		Important	connected to this unit.
			1 Press M.C. to turn AUX on or off.
	PW SAVE (power saving) is cancelled if the vehi-
			USB PNP (plug and play)
	cle battery is disconnected and will need to be
	turned back on once the battery is reconnected.		This setting allows you to switch your source to USB/
	When PW SAVE (power saving) is off, depending		iPod automatically.
	on connection methods, the unit may continue to		1 Press M.C. to turn the plug and play function on
			or off.
	draw power from the battery if your vehicle’s igni-
			ON – When a USB storage device/iPod is con-
	tion doesn’t have an ACC (accessory) position.
			nected, depending on the type of device, the
	1 Press and hold SRC/OFF until the unit		source is automatically switched to USB/iPod
			when you turn on the engine. If you disconnect
	turns off.
			your USB storage device/iPod, this unit’s source
	2 Press SRC/OFF and hold until function		is turned off.
			OFF – When a USB storage device/iPod is con-
	name appears in the display.
			nected, the source is not switched to USB/iPod
	3 Turn M.C. to select the initial setting.		automatically. Please change the source to USB/
			iPod manually.
	After selecting, perform the following proce-
			REAR-SP (rear output setting)
	dures to set the initial setting.
			The rear speaker leads output can be used for full-
	CLOCK SET (setting the clock)
			range speaker or subwoofer connection.
	1 Press M.C. to display the setting mode.		If you switch to SW, you can connect a rear speaker
			lead directly to a subwoofer without using an auxiliary
	2 Press M.C. to select the segment of the clock dis-		amp.
		play you wish to set.	Initially, REAR-SP is set for rear full-range speaker
		Hour—Minute	connection (FUL).
	3 Turn M.C. to adjust the clock.		1 Press M.C. to select the desired setting.
	CLOCK (clock display)		FUL—SW
			! Even if you change this setting, there will be
	You can turn the clock display on or off.		no output if you select OFF in SUB.W (Refer to
	The clock display disappears temporarily when you		SUB.W (subwoofer on/off setting) on the pre-
	perform other operations, but the clock display ap-		vious page).
	pears again after 25 seconds.		! If you change this setting, subwoofer output
	1 Press M.C. to turn the clock display on or off.		in the audio menu will return to the factory
			settings.
	FM STEP (FM tuning step)
			PREOUT (preout setting)
	Normally, the FM tuning step employed by seek tun-
			The RCA outputs can be used for rear speaker or sub-
	ing is 50 kHz. When AF or TA is on, the tuning step
	automatically changes to 100 kHz. It may be prefer-		woofer connection.
	able to set the tuning step to 50 kHz when AF is on.		If you switch to SW, you can connect a rear speaker
	! The tuning step remains at 50 kHz during manual		lead directly to a subwoofer without using an auxiliary
		tuning.	amp.
	1 Press M.C. to select the FM tuning step.		Initially, PREOUT is set for rear full-range speaker con-
		50 (50 kHz)—100 (100 kHz)	nection (SW).
			1 Press M.C. to select the desired setting.
	AUTO-PI (auto PI seek)
			SW—REA
	The unit can automatically search for a different sta-		! Even if you change this setting, there will be
			no output if you select OFF in SUB.W (Refer to
	tion with the same programming, even during preset
			SUB.W (subwoofer on/off setting) on the pre-
	recall.
			vious page).
	1 Press M.C. to turn Auto PI seek on or off.
			! If you change this setting, subwoofer output
	AUX (auxiliary input)		in the audio menu will return to the factory
			settings.
			DEMO (demo display setting)

18 En