Pioneer DEH-P780MP installation manual Function, AUX input jack 3.5 ø, 23 cm 9, Power amp

INSTALLATION MANUAL

DEH-P780MP

This product conforms to CEMA cord colors.

Le code de couleur des câbles utilisé pour ce produit est conforme à CEMA.

Printed in Thailand

Imprimé en Thaïlande

<CRD4086-A/N> UC <KMMZX> <06A00000>

MANUEL D’INSTALLATION

Connecting the Units

Note:

•This unit is for vehicles with a 12-volt battery and negative grounding. Before installing it in a recre- ational vehicle, truck, or bus, check the battery voltage.

•To avoid shorts in the electrical system, be sure to disconnect the ≠ battery cable before beginning installation.

•Refer to the owner’s manual for details on connecting the power amp and other units, then make connections correctly.

•Secure the wiring with cable clamps or adhesive tape. To protect the wiring, wrap adhesive tape around them where they lie against metal parts.

•Route and secure all wiring so it cannot touch any moving parts, such as the gear shift, handbrake and seat rails. Do not route wiring in places that get hot, such as near the heater outlet. If the insulation of the wiring melts or gets torn, there is a danger of the wiring short-circuiting to the vehicle body.

•Don’t pass the yellow lead through a hole into the engine compartment to connect to the battery. This will damage the lead insulation and cause a very dangerous short.

•Do not shorten any leads. If you do, the protection circuit may fail to work when it should.

•Never feed power to other equipment by cutting the insulation of the power supply lead of the unit and tapping into the lead. The current capacity of the lead will be exceeded, causing overheating.

•When replacing the fuse, be sure to only use a fuse of the rating prescribed on the fuse holder.

•Since a unique BPTL circuit is employed, never wire so the speaker leads are directly grounded or the left and right ≠ speaker leads are common.

•Speakers connected to this unit must be high- power with minimum rating of 50 W and imped- ance of 4 to 8 ohms. Connecting speakers with out- put and/or impedance values other than those noted here may result in the speakers catching fire, emitting smoke or becoming damaged.

•When this product’s source is switched ON, a con- trol signal is output through the blue/white lead. Connect to an external power amp’s system remote control or the car’s Auto-antenna relay control ter- minal (max. 300 mA 12 V DC). If the car features a glass antenna, connect to the antenna booster power supply terminal.

•When an external power amp is being used with this system, be sure not to connect the blue/white lead to the amp’s power terminal. Likewise, do not connect the blue/white lead to the power terminal of the auto-antenna. Such connection could cause excessive current drain and malfunction.

•To avoid a short-circuit, cover the disconnected lead with insulating tape. Insulate the unused speaker leads without fail. There is a possibility of a short-circuit if the leads are not insulated.

•To prevent incorrect connection, the input side of the IP-BUS connector is blue, and the output side is black. Connect the connectors of the same colors correctly.

•If this unit is installed in a vehicle that does not have an ACC (accessory) position on the ignition switch, the red lead of the unit should be connected to a terminal coupled with ignition switch ON/OFF operations. If this is not done, the vehicle battery may be drained when you are away from the vehi- cle for several hours. (Fig.1)

		CC
	F	A	O				F	O
			N					N
O	F					O	F
					S					S
					T					T
				R	A				R	A
			T					T
ACC position						No ACC position

Fig. 1

•The black lead is ground. Please ground this lead separately from the ground of high-current prod- ucts such as power amps.

If you ground the products together and the ground becomes detached, there is a risk of damage to the products or fire.

•Cords for this product and those for other products may be different colors even if they have the same function. When connecting this product to another product, refer to the supplied manuals of both products and connect cords that have the same

function.

						<ENGLISH>
	AUX input jack (3.5 ø)		Subwoofer output
	Use a stereo mini plug cable	23 cm (9 in.)	(SUBWOOFER OUTPUT)			Power amp
						(sold separately)
	to connect with auxiliary
	equipment.		Rear output
Antenna jack		IP-BUS input (Blue)	(REAR OUTPUT)			Power amp
	15 cm (5-7/8 in.)					(sold separately)
			Front output
			(FRONT OUTPUT)			Power amp
			15 cm (5-7/8 in.)			(sold separately)
	This product
		Jack for the Wired Remote Control Adaptors			Connecting cords with RCA pin
					plugs (sold separately)
		Please see the Instruction Manual for the Wired
		Remote Control Adaptors (sold separately).
			Multi-CD player
Yellow/black		IP-BUS cable	(sold separately)
If you use an equipment with Mute function,
wire this lead to the Audio Mute lead on that		Blue/white			System remote control
equipment. If not, keep the Audio Mute lead
free of any connections.		To system control terminal of the power
		amp or Auto-antenna relay control
		terminal (max. 300 mA 12 V DC).
Yellow	Fuse (10 A)		+			+
To terminal always supplied with power			Front speaker			Front speaker
regardless of ignition switch position.			≠			≠
Red	Fuse resistor
To electric terminal controlled by ignition				White	Gray
switch (12 V DC) ON/OFF.			+			+
			Front speaker			Front speaker
Orange/white	Fuse resistor		≠	White/black	Gray/black	≠
			Left			Right
To lighting switch terminal.
			+	Green	Violet	+
Black (ground)			Rear speaker			Rear speaker
			≠			≠
To vehicle (metal) body.				Green/black	Violet/black
	With a 2 speaker system, do not connect		+			+
	anything to the speaker leads that are not		Rear speaker			Rear speaker
	connected to speakers.		≠			≠
	Perform these connections when using the		+			+
			Subwoofer			Subwoofer
	optional amplifier.
			≠			≠

Fig. 2