Before Using This Product

Setting the Unit

• To adjust the switch, use standard tip screwdriver if needed.

BRIDGEABLE FOUR-CHANNEL

POWER AMPLIFIER

AMPLIFICADOR DE POTENCIA DE

CUATRO CANALES EN PUENTE

Owner’s Manual

PRS-D4100F

Manual del Propietario

PIONEER CORPORATION

4-1, MEGURO 1-CHOME, MEGURO-KU, TOKYO 153-8654, JAPAN

Thank you for purchasing this PIONEER product. Before attempting operation, be sure to read this manual.

In case of trouble

When the unit does not operate properly, contact your dealer or the nearest autho- rized PIONEER Service Station.

CAUTION

Never replace the fuse with one of greater value or rating than the original fuse. Use of an improper fuse could result in over- heating and smoke and could cause dam- age to the product and injury including burns.

CAUTION

Diagram A - Proper		Diagram B - Improper
	8		4
	+ Ohm -		+ Ohm -
	Speaker		Speaker
	8		4
	+ Ohm -		+ Ohm -
	Speaker		Speaker
L+	R-	L+	R-
	Pioneer		Pioneer
	Amplifier		Amplifier

or use a single 4 Ω speaker per channel. If you have any questions or concerns, please contact your local authorized Pioneer dealer or call Pioneer customer service.

WARNING

• Always use the special red battery and ground

wire [RD-223], which is sold separately. Connect

the battery wire directly to the car battery positive

terminal (+) and the ground wire to the car body.

• Do not touch the amplifier with wet hands.

Otherwise you may get an electric shock. Also, do

not touch the amplifier when it is wet.

• For traffic safety and to maintain safe driving

conditions, keep the volume low enough so that

you can still hear normal traffic sound.

• Check the connections of the power supply and

speakers if the fuse of the separately sold battery

wire or the amplifier fuse blows. Detect the cause

and solve the problem, then replace the fuse with

another one of the same size and rating.

• To prevent malfunction of the amplifier and

speakers, the protective circuit will cut the power

supply to the amplifier (sound will stop) when an

abnormal condition occurs. In such a case, switch

the power to the system OFF and check the

connection of the power supply and speakers.

Detect the cause and solve the problem.

• Contact the dealer if you cannot detect the cause.

• To prevent an electric shock or short-circuit

during connection and installation, be sure to

disconnect the negative (–) terminal of the battery

beforehand.

Terminal Cover

Before setting up the unit, unfasten the screws with a 4 mm hexagonal wrench and remove the terminal cover.

Cut Off Frequency Control

If the LPF/HPF select switch is set to LPF or HPF, you can select a cut off frequency from 40 Hz to 500 Hz.

LPF (Low-Pass Filter)/HPF (High-Pass Filter) Select Switch

Set the LPF/HPF select switch as follows according to the type of speaker that is connected to the speaker output connector and the car stereo system:

LPF/HPF Select	Audio frequency range	Speaker	Remarks
Switch	to be output	Type
LPF (Left)	* — 40 Hz to 500 Hz	Subwoofer	Connect a subwoofer.

OFF (Center)	Full range	Full range
HPF (Right)	* 40 Hz to 500 Hz —	Full range	Use if you want to cut the
			very low frequency range*
			because it is not necessary
			for the speakers you are
			using.

* See the “Cut Off Frequency Control” section.

Input Select Switch

For two-channel input, slide this switch to the left. For four-channel input, slide this switch to the right.

Power Indicator

The power indicator lights when the power is switched on.

PIONEER ELECTRONICS (USA) INC.

P.O. Box 1540, Long Beach, California 90801-1540, U.S.A. TEL: (800) 421-1404

PIONEER EUROPE NV

Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium TEL: (0) 3/570.05.11

PIONEER ELECTRONICS ASIACENTRE PTE. LTD.

253 Alexandra Road, #04-01, Singapore 159936 TEL: 65-6472-7555

PIONEER ELECTRONICS AUSTRALIA PTY. LTD.

178-184 Boundary Road, Braeside, Victoria 3195, Australia TEL: (03) 9586-6300

PIONEER ELECTRONICS OF CANADA, INC.

300 Allstate Parkway, Markham, Ontario L3R OP2, Canada TEL: 1-877-283-5901

PIONEER ELECTRONICS DE MEXICO, S.A. de C.V.

Blvd.Manuel Avila Camacho 138 10 piso Col.Lomas de Chapultepec, Mexico, D.F. 11000 TEL: 55-9178-4270

Printed in China

Impreso na China

4 Ohm Bridged Mode

2 Ohm Bridged Mode

Do NOT install or use your Pioneer ampli- fier by wiring speakers rated at 4 Ohm (or lower) in parallel to achieve a 2 Ohm (or lower) bridged mode (Diagram B). Amplifier damage, smoke, and overheating could result from improper bridging. The amplifier surface could also become hot to the touch and minor burns could result.

To properly install or use a bridged mode for a two-channel amplifier and achieve a 4

Ωload, wire two 8 Ω speakers in parallel

with Left + and Right – (Diagram A) or use a single 4 Ω speaker. For a four-channel amplifier, follow the speaker output con- nection diagram for bridging as shown on the back of your amplifier, and wire two 8

Ωspeakers in parallel to achieve a 4 Ω load

• Confirm that no parts are behind the panel when

drilling a hole for installation of the amplifier. Be

sure to protect all cables and important equipment

such as fuel lines, brake lines and the electrical

wiring from damage.

• DO NOT allow amplifier to come into contact

with liquids due to, for example, the location

where the amplifier is installed. Electrical shock

could result. Also, amplifier and speaker damage,

smoke, and overheating could result from contact

with liquids. In addition, the amplifier surface and

the surface of any attached speakers could become

hot to the touch and minor burns could result.

Input Switch

It is possible to input from a car stereo external output (subwoofer output) or a car stereo speaker output. When using an external output (subwoofer output), slide the switch to the left. For connec- tion instructions, see the “Connection Diagram” section. When using a speak- er output, slide the switch to the right. In this case, it is necessary to use the supplied speaker input wire with RCA pin cord. For details, see the “Using the Speaker Input” section.

BFC (Beat Frequency Control) Switch

BFC switch is on the bottom of the unit. If you hear a beat while listening to an AM broadcast with your car stereo, change the BFC switch using a small standard tip screwdriver.

Gain Control

Adjusting the gain controls A and B will help match the output of the car stereo to the Pioneer amplifier. Normally, set the gain controls to the NORMAL position. If the output is low, even when the volume of the car stereo is turned up, turn these controls clockwise. If there is dis- tortion when the volume of the car stereo is turned up, turn these controls counter-clockwise.

•If you only use one input plug, set the gain controls for speaker outputs A and B to the same position.

•When using with an RCA equipped car stereo (standard output of 500 mV), set to the NORMAL position. When using with an RCA equipped Pioneer car stereo with max. output of 4 V or more, adjust level to match the car stereo output level.

<YRD5128-A/U> ES

PRS-D4100F specifications

The Pioneer PRS-D4100F is a high-performance car amplifier designed to deliver exceptional sound quality and power while maintaining a compact size. This amplifier is engineered for audiophiles who demand both reliability and performance in their automotive audio systems.

One standout feature of the PRS-D4100F is its powerful 4-channel output. It can produce a peak power of up to 1,000 Watts, providing ample power to drive multiple speakers or subwoofers simultaneously. Each channel can deliver a RMS power of 100 Watts at 4 ohms, ensuring that your audio experience is both clear and dynamic, even at high volumes. This powerful output capability makes the PRS-D4100F suitable for various speaker setups, enhancing audio quality across the entire frequency spectrum.

The amplifier incorporates high-quality components and advanced technologies, such as Pulse Width Modulation (PWM) circuitry and a MOSFET power supply. PWM allows for efficient power conversion, resulting in less heat generation and increased reliability during prolonged use. The MOSFET technology further improves efficiency and performance, providing faster dynamic response and superior sound accuracy.

In addition to its robust performance specs, the PRS-D4100F also features multiple integration options. It supports both high-level inputs, making it easy to connect to factory-installed audio systems, and low-level RCA inputs for aftermarket setups. This flexibility allows users to incorporate the amplifier into various audio configurations seamlessly.

To ensure optimal performance, the PRS-D4100F includes adjustable crossover settings. This feature allows users to tailor the frequency response of the amplifier, enabling a customized listening experience. The low-pass filter, high-pass filter, and full-range capabilities provide users with the ability to match their audio system perfectly to their listening preferences.

The sleek and sturdy design of the PRS-D4100F is another attractive aspect. Its compact size allows for versatile installation options, making it easier to fit in different vehicle types and configurations. The amplifier is built with a durable chassis that ensures protection against vibrations and heat, contributing to its longevity.

In conclusion, the Pioneer PRS-D4100F is a feature-rich amplifier that combines power, efficiency, and adaptability. With its impressive output capabilities, advanced technologies, and user-friendly features, it stands out as a top choice for anyone looking to enhance their car audio experience. Whether you’re looking to improve your factory sound system or build a complete aftermarket setup, the PRS-D4100F delivers audio performance that meets the demands of even the most discerning listeners.

Pioneer PRS-D4100F owner manual Before Using This Product, Setting the Unit

Models: PRS-D4100F