Planet Technology SGSW-4802 NOT, NOTE

Figure 3-28: The Logout Web Page

!If you changed a new IP Address for the management switch, the systems will NOT

NOTE	automatically changed to the new IP address after you click on the “Logon” button.

Contents

Page Trademarks Disclaimer FCC Warning CE Mark Warning Revision TABLE OF CONTENTS Page 1. INTRODUCTION 1.1 Checklist 1.2 About the Switch 1.3 Features 1.4 Specification Page 2. HARDWARE DESCRIPTION 2.1Front Panel 2.2 Rear Panel 2.3Hardware Installation 2.3.1 Connecting end node or hub or switch 2.3.2 Connecting to Network Backbone or Server 2.4 Terminal Setup 2.5 IP Configuration sys set ip sys set ip 192.168.0.2 255.255.255.0 3. WEB-BASEDMANAGEMENT 3.1 Configuration 3.2 Web Pages 3.3 Port Config Choose Port Speed/ Duplex ‘Auto’: ‘10Mbps HD’: ‘10Mpbs FD’: 3.4 VLAN Config Setup Procedures 3.5 Trunk config Port Trunking Setup Procedures 3.6 Advanced Configuration 3.7 STP Config 3.7.1 STP Port Description of Parameters 3.7.2 STP Bridge 3.8.1 IGMP Management 3.8.2 Definition on IGMP v1.0 and 3.8 IGMP 3.9 Stack Step 5: Step 6: Page 3.10 SNMP 3.11 RMON Statistics 3.12 Port Security 3.12.1 Setting Up Procedures 3.12.2 Delete MAC Address For deleting individual MAC Address For deleting ALL MAC Addresses 3.13 Mirror Port 3.13.1 Using Mirror Port to Monitor Traffic 3.13.2 Setup Procedures 3.14 Aging Control Aging Control Configuration Procedures 3.15 Address Search 3.15.1 Host Searching Procedures 3.15.2 MAC Address Search MAC Address Search Procedures 3.16 System Tools 3.17 System Config 3.18 System Information 3.19 Change Password Changing password procedure 3.20 Firmware Upgrade Upgrade Firmware Procedure Page 3.21 Save & Reboot 3.21.1 Save 3.21.2 Backup Page 3.21.3 Restore 3.21.4 Clear and Reset 3.22 Message Windows 3.23 Reboot Switch 3.24 Logout NOT 4. CONSOLE INTERFACE 4.1 CONNECT TO PC 4.2 Logging on to the Switch sys--SystemManagement Commands Logout--ExitManagement Commands Port--PortManagement Commands igmp--IGMPManagement Commands igmp show 4.2.1. sys--SystemManagement Commands 4.2.1.2 sys show ip 4.2.1.3 sys show mac 4.2.1.4 sys search ip <IP Address sys search ip <ddd.ddd.ddd.ddd 4.2.1.5 sys search mac <MAC Address sys search mac <hh-hh-hh-hh-hh-hh 4.2.1.6 sys set ip <IP Address> <Subnet Mask> <Default Gateway 4.2.1.7 sys set name "string 4.2.1.8 sys set contact "string 4.2.1.9 sys set location "string 4.2.1.10 sys set password 4.2.1.11 sys set link_info <on|off 4.2.1.12 sys aging <aging_time 4.2.1.13 sys reset system 4.2.1.14 sys reset config 4.2.1.15 sys save config 4.2.2 logout 4.2.3 port--PortManagement Commands 4.2.3.1 port show stat 4.2.3.2 port show mir 4.2.3.3 port show sec <port number 4.2.3.4 port show rmonstat <port number 4.2.3.5 port set enable <port number> [-h|-f] [-10|-100|-1000] [-A] 4.2.3.6 port set disable <port number 4.2.3.7 port set flw <port number> <on|off 4.2.3.8 port set bck <port number> <on|off 4.2.3.9 port set pri <port number> <-ppriority 4.2.3.10 port set vid <port number> <-vvid 4.2.3.11 port set mir <port number> [-mmirror_port] 4.2.3.12 port sec add <port number> <MAC Address 4.2.4. vlan--VLANManagement Commands 4.2.4.1 vlan show 4.2.4.2 vlan build <vid> <-uuntags> <-ttags> <-ppriority 4.2.4.3 vlan delete <vid 4.2.5 trunk--TRUNKManagement Commands 4.2.6. stp--STPManagement Commands 4.2.6.2 stp show port 4.2.6.3 stp show bridge 4.2.6.4 stp set port <port number> <-cPathCost 4.2.6.5 stp set port <port number> <-ppriority 4.2.6.6 stp set bridge <-pRootPriority 4.2.6.7 stp set bridge <-tHelloTime 4.2.6.8 stp set bridge <-dForwardDelay 4.2.7 snmp--SNMPManagement Commands 4.2.7.2 snmp show community 4.2.7.3 snmp set <-ro|-rw>"CommunityString 4.2.8 stack--STACKManagement Commands 4.2.9 igmp--IGMPManagement Commands 4.2.9.2 igmp [on [ver version]|off] 5. SWITCH OPERATION 5.1 Address Table 5.2 Learning 5.3 Forwarding & Filtering 5.4 Store-and-Forward 6. TROUBLESHOOTING APPENDIX A NETWORKING CONNECTION A.1 Switch‘s RJ-45Pin Assignments A.2 10/100Mbps, 10/100Base-TX A.3 RJ-45cable pin assignment