![](/images/new-backgrounds/1139438/1394389x1.webp)
UK
15.Never install telephone wiring during a lightning storm.
16.Never install telephone sockets in wet locations unless the socket is specifically designed for wet locations.
17.Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface.
18.Use caution when installing or modifying telephone lines.
19.Keep all product cords and cables away from operating machinery.
Plantronics B.V. hereby declares that this T10 Headset Telephone is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.
A copy of the Declaration of Conformity to the essential requirements of 1999/5/EC may be found at www.plantronics.com/documentation.
SETUP
Fig. A. Connect the telephone to the telephone wall socket using the Line Cable.
Fig. B. Turn the T10 base over and insert the Headset Stand.
Set the Ringer Volume Control for incoming calls to your preferred level.
Plug the Headset Cable into the Headset Socket.
For most users, the Flash Button
should be set to 3, however, if this does not work try other settings. This will not harm the T10, the telephone system or your telephone line.
USING THE HEADSET
The Headset included with the T10 Headset Telephone can be used with the Adjustable Headband or with one of the Ear Loops.
HEADBAND USE
Fig. C. Snap the Adjustable Headband into the back of the Headset Assembly. Press the Ear Cushion Assembly onto the Headset Assembly, aligning the notch in the ring with the Microphone Boom.
Fig. D. Place the Headset on either ear and adjust to a comfortable position by moving the Adjustable Headband. Position the Microphone Boom near the corner of your mouth.
|
|
|
| UK |
|
|
|
|
|
| EAR LOOP USE |
|
| UK |
| Fig. E. Press the Pivot Ball Ring onto the Headset Assembly. Insert one of the | |||
|
| |||
| ear loops into the Pivot Ball. You may need to try each size to find the |
| ||
| most comfortable fit. Slip the ear loop over your ear and position the |
| ||
| Microphone Boom near the corner of your mouth. | D | ||
| CLOTHING CLIP |
|
|
|
| Fig. F. The Clothing Clip keeps the Headset free from the weight of the Headset | DK | ||
| Cable. Attach the clip to your clothing at about chest level. Allow enough | |||
|
| |||
| slack in the cable (approximately 15cm) to permit your head to move |
| ||
| without pulling on the Headset or the Clothing Clip. You are now ready |
| ||
| to make or receive calls. |
| E | |
|
|
|
| |
| PLACING A CALL |
|
| |
| Fig. G. With the Headset in position, place a call by pressing the Headset | F | ||
| Button | |||
|
| |||
| for a dial tone. Dial the desired number using the Twelve Button Dial Pad. |
| ||
| When your caller answers, speak normally. If your caller cannot hear you, |
| ||
| see Troubleshooting (page 11). Adjust the Listen Volume Control and the | I | ||
| Tone Control as needed to hear your caller. |
| ||
| RECEIVING A CALL |
| N | |
| With the Headset in position, when the ringer notifies you of an incoming call, press | |||
|
| |||
| the Headset Button | to answer the call. |
| |
| Lights are on). |
|
| NL |
| PRODUCT FEATURES |
| ||
|
|
| ||
| REDIAL |
|
|
|
| The base unit will store the last number dialed. The last number can be automatically | P | ||
| redialed by pressing the Redial Button | . |
| |
| FLASH |
|
|
|
| If your telephone service includes call waiting, the button allows you to switch | SF | ||
| between two calls. When your telephone alerts you to a second call, press the | |||
|
| |||
| button to place the current call on hold and to immediately connect you to the |
| ||
| second call. Press the | button again to return to the first caller. This feature can |
| |
|
|
|
| S |
9 |
| 10 |