Polk Audio LC265i LC80i-IPHardware, LC80i-IPDimension, LC80i-IPPerformance Enclosure Dimensions

LC80i-IP Hardware

•One LC80i-IP speaker

•Performance Optimization Wizard – CD-ROM

•Euro-style (Phoenix) power supply connector

•Mounting template

• Paint mask

• Weather-resistant aluminum grille and stainless steel hardware

•LCi-IP manual

•Laminated configuration setup card

•Registration card

Note: If you are setting up LCi-IP speakers to be controlled via an IP-network such as NetStreams™ Digilinx™, purchase a network card, which is sold separately, from NewStreams™. The network card will control up to one pair of speakers.

Important Note: If anything is missing or damaged, or if your LCi-IP speak- er fails to operate, notify Polk Audio Installer Support Services immediately at 800-377-7655.

Accessories (not included)

•Performance Enclosure for exact volume enclosure performance in pre-build installations. Improves bass performance and sound isolation. Model number: ENCL 80IP.

•Speaker-level-to-line-level transformer, such as the PAC SNI-35.

(For analog installations only. Powers up to 4 each LC80i-IP speakers.)

•SPS-1 Power Supply (a power supply is required).

Cutout

Dimension

9 7/16"

(23.9 cm)

Total

Depth

7 7/16"

(18.9 cm)

LC80i-IP Dimension

Outer Diameter 10 3/4" (27.3cm)

Available Finish: Paintable White

LC80i-IP Performance Enclosure Dimensions

20 5/8" H x 13" W x 9" D (51.8cm x 33.0cm x 22.9cm)

LC265i-IP Specifications

P E R F O R M A N C E

OVERALL FREQ. RESPONSE		20Hz-27kHz
FREQ. RESPONSE -3DB LIMIT		35Hz-27kHz
ANALOG AUDIO SIGNAL
VOLTAGE INPUT (LINE-LEVEL) FULL OUTPUT		2V RMS
AMPLIFIER SNR		> 90DB
FIRMWARE UPGRADABLE		YES
MID-BASS DRIVER		1–6.5"(16.5CM) MINERAL POLYPROPYLENE
		CONE, RUBBER SURROUND;
WOOFER		1–6.5"(16.5CM) AERATED POLY-
		PROPYLENE CONE WITH 1.5" VOICE COIL
TWEETER	1" (2.5CM) RING RADIATOR IN SWIVEL MOUNT
OUTSIDE DIMENSIONS		8 1/2" X 20 7/8" (21.59CM X 53.04CM)
CUTOUT DIMENSIONS		7 1/4" X 19 1/4" (18.42CM X 48.90CM)
MOUNTING DEPTH (WITH 1/2" DRYWALL)		3 1/16" (7.78CM)
INSTALLED WEIGHT		8.7 LBS (3.9kg)
SHIPPING WEIGHT		11.6 LBS (5.3kg)

P O W E R C O N T I N U O U S R AT I N G S

200W speaker with < 0.5% THD+N (25W tweeter 4 Ohms, 75W mid 8 Ohms, 100W woofer 8 Ohms)

P O W E R R E Q U I R E M E N T S P E R S P E A K E R

VOLTAGE INPUT	48VDC
CURRENT DRAW	4.5A MAXIMUM

LC80i-IP Specifications

P E R F O R M A N C E

OVERALL FREQ. RESPONSE		25Hz-27kHz
FREQ. RESPONSE -3DB LIMIT		40Hz-27kHz
ANALOG AUDIO SIGNAL
VOLTAGE INPUT (LINE-LEVEL) FULL OUTPUT		2V RMS
AMPLIFIER SNR		> 90DB
FIRMWARE UPGRADABLE		YES
MID-BASS DRIVER		1–8"(20.3CM) COMPOSITE POLYPROPYLENE
		CONE, RUBBER SURROUND
TWEETER	1"(2.5CM) RING RADIATOR IN SWIVEL MOUNT
OUTSIDE DIMENSIONS		10 3/4" DIA (27.3CM)
CUTOUT DIMENSIONS		7 3/8" DIA (18.7CM)
MOUNTING DEPTH (WITH 1/2" DRYWALL)		6 15/16" (17.6CM)
INSTALLED WEIGHT		4.8 LBS (2.2kg)
SHIPPING WEIGHT		6.8 LBS (3.1kg)

P O W E R C O N T I N U O U S R AT I N G S

100W speaker with < 0.5% THD+N (25W tweeter 4 Ohms, 75W mid 4 Ohms)

P O W E R R E Q U I R E M E N T S P E R S P E A K E R

VOLTAGE INPUT	48V	OR 28VDC
CURRENT DRAW	2.3A	@ 48V, OR
	3.8A @ 28V MAXIMUM

Power Supply

The SPS-1 power supply was specifically designed to produce clean, reliable power to ensure that all Polk Audio LCi-IP loudspeakers perform to their maximum capabilities. All output connectors are protected against short circuit and over current.

Power Connectors

For optimum performance, we recommend using 14-gauge, 4-conductor wire between the power supply and each amplifier (see the LCi-IP manual for other wiring options).

LC265i-IP and LC80i-IP Specifications

I N H E R E N T D E L AY

C O N T R O L S A N D A D J U S T M E N T S

Specifications

Output
Voltage	48VDC	IEC Socket
Current	8A (Max continuous)
Input		This is a standard
		IEC socket.
Voltage Range	100-240 VAC Nominal Auto Switching
Frequency	50-60Hz
Current Draw	8A (120V)
	3.5A (240V)
Dimensions
Width	4.9" (125mm)
Height	3.1" (79mm) , 3 11/16"(93.6mm) with feet
Length	14" (358mm)
Shipping Weight	8.4lbs (4kgs)
Protection	Thermal, short circuit,current/power overdraw
Fuse Replacement	T8AH500V

Note: Leave at least 2-3 inches of clearance on the sides and top of the power supply.

Capabilites

SPS-1 will power 2 LC265i-IP speakers or 4 LC80i-IP speakers.

INHERENT DELAY FOR EACH SPEAKER IS:
-2.5 MILLISECONDS	-4.4 MILLISECONDS

ANY OTHER DELAY IS FROM THE MULTI-ROOM AUDIO VISUAL (MRAV).

P R O T E C T I O N C I R C U I T R Y

Thermal, short-circuit, current overdraw, clipping compresser/limiter, reverse polarity

(Performance Optimization Wizard Program)

COMPUTER REQUIREMENTS
OPERATING SYSTEM	WINDOWS XP
USB PORT	5-WIRE USB 1.1	CONNECTOR
HARD DRIVE	5	MEGABYTES

REQUIRED SPEAKER CONNECTIONS

TO CONNECT YOUR COMPUTER TO THE SPEAKER, YOU HAVE TWO OPTIONS:

1.USB PORT (ANALOG USE ONLY)

2.ETHERNET JACK WITH NETWORK DECODER CARD (SOLD SEPARATELY).

2

P o l k A u d i o C u s t o m I n s t a l l P r o d u c t : L C 2 6 5 i - I P , L C 8 0 i - I P w w w . P o l k A u d i o . c o m / 8 0 0 . 3 7 7 . 7 6 5 5 ( U S A & C a n a d a ) / 4 1 0 . 3 5 8 . 3 6 0 0 ( W o r l d w i d e )

3