90550119 PC1800JS Jig Saw 4/9/09 7:52 AM Page 12

METAL CUTTING

In cutting thin gauge sheet metals, it is best to clamp wood to the bottom of sheet metal; this will insure a clean cut without the risk of vibration or tearing of metal. Always remember to use a finer blade for ferrous metals (for those that have a high iron content); and use a coarser blade for non-ferrous metals (those that do not have an iron content). Use a high speed setting for cutting soft metals (aluminum, copper, brass, mild steel, galvanized. pipe, conduit sheet metal, etc.). Use lower speed to cut plastics, tile, laminate, hard metals, and cast iron. Spread a film of oil along the intended line of cut for easier operation and longer blade life. For cutting aluminum, kerosene is preferred.

RIP & CIRCLE CUTTING

Ripping and circle cutting without a pencil line are easily done with the a rip fence and circle guide (available at extra cost).

When ripping, slide the rip fence under the screw from either side of the saw. Set the cross bar at desired distance from blade and tighten screw. For ripping, the cross bar should be down and against the straight edge of the workpiece as shown in figure I.

When circle cutting, adjust rip fence so that distance from blade to hole in cross bar is at the desired radius and tighten screw. Place saw so that hole in cross bar is over center of circle to be cut (drill hole for blade or cut inward from edge of material to get blade into position). When saw is properly positioned, drive a small nail through hole in cross bar. Using rip fence as a pivot arm, begin cutting circle. For circle cutting, the cross bar should be up, as shown in figure J.

I

J

THE RBRC™ SEAL

The RBRC™ (Rechargeable Battery Recycling Corporation) Seal on the LI-ION or NI-CD battery (or battery pack) indicates that the costs to recycle the battery (or battery pack) at the end of its useful life have already been paid by

PORTER-CABLE. RBRC™ in cooperation with PORTER-CABLE and other battery users, has established programs in the United States to facilitate the collection of spent LI-

ION or NI-CD batteries. Help protect our environment and conserve natural resources by returning the spent LI-ION or NI-CD battery to an authorized PORTER-CABLE service center or to your local retailer for recycling. You may also contact your local recycling center for information on where to drop off the spent battery.

RBRC™ is a registered trademark of the Rechargeable Battery Recycling Corporation.

MAINTENANCE

Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the tool; never immerse any part of the tool into a liquid.

REPLACEMENT PARTS

Use only identical replacement parts. For a parts list or to order parts, visit our service website at www.portercable.com. You can also order parts from your nearest PORTER-CABLE Factory Service Center or PORTER-CABLE Authorized Warranty Service Center. Or, you can call our Customer Care Center at (888) 848-5175.

12

Page 11 Page 13
Page 12
Image 12
Porter-Cable PC1800JS, 90550119 Rbrc Seal, Metal Cutting, RIP & Circle Cutting, Maintenance, Replacement Parts
Page 11 Page 13

PC1800JS, 90550119 specifications

The Porter-Cable 90550119 PC1800JS is an exceptional jig saw that stands out in the power tool market. Known for its user-friendly design and robust performance, this tool is ideal for both professional craftsmen and DIY enthusiasts. It delivers a combination of precision, power, and versatility that makes it indispensable for a variety of cutting tasks.

One of the main features of the PC1800JS is its powerful 6.5-amp motor, which provides ample power for tackling tough materials. This motor is designed to maintain consistent speed under heavy load, ensuring smooth cuts every time. The jig saw operates with a variable speed control feature that allows users to adjust the speed from 0 to 3,000 strokes per minute. This versatility makes it suitable for a wide range of materials, including wood, metal, and plastic.

The jig saw is equipped with an orbital action feature that offers four settings, allowing users to customize the cutting action based on their specific needs. This feature enhances cutting efficiency and provides smoother finishes on different materials. The adjustable shoe of the PC1800JS enables users to make bevel cuts up to 45 degrees, making it a valuable tool for projects requiring angled cuts.

In terms of design, the PC1800JS is ergonomically shaped for maximum comfort during extended use. The rubber over-mold handle provides a secure grip, reducing user fatigue for prolonged operations. The tool also includes an integrated dust blower that keeps the cutting line clear of debris, improving visibility and accuracy during cuts.

Another standout characteristic of the Porter-Cable PC1800JS is its tool-less blade change system. This feature allows for quick and easy blade changes, enabling users to switch between various blade types without the need for additional tools. The jig saw is compatible with both T-shank and U-shank blades, providing users with ample options to tackle different projects.

In summary, the Porter-Cable 90550119 PC1800JS jig saw combines powerful performance with innovative features and ease of use. With its adjustable speed settings, orbital action, and comfortable design, it is well-equipped to handle a variety of cutting tasks, making it a valuable addition to any toolkit. Whether for professional use or home improvement projects, the PC1800JS stands as a reliable choice for achieving precise and clean cuts every time.
Top Page Image Contents