Poulan 177937 owner manual Assembly, INSTALL SEAT See Fig

ASSEMBLY

INSTALL SEAT (See Fig. 3)

Adjust seat before tightening adjustment knob.

•Remove adjustment knob and flat washer securing seat to cardboard packing and set aside for assembly of seat to tractor.

•Pivot seat upward and remove from the cardboard packing. Remove the cardboard packing and discard.

•Place seat on seat pan so head of shoulder bolt is positioned over large slotted hole in pan.

•Push down on seat to engage shoulder bolt in slot and pull seat towards rear of tractor.

•Pivot seat and pan forward and assemble adjustment knob and flat washer loosely. Do not tighten.

•Lower seat into operating position and sit on seat.

•Slide seat until a comfortable position is reached which allows you to press clutch/brake pedal all the way down.

•Get off seat without moving its adjusted position.

•Raise seat and tighten adjustment knob securely.

SEAT

SEAT PAN

SHOULDER

BOLT

FLAT WASHER

ADJUSTMENT

KNOB

FIG. 3

NOTE: You may now roll or drive your tractor off the skid. Follow the appropriate instruction below to remove the tractor from the skid.

TO ROLL TRACTOR OFF SKID (See Opera- tion section for location and function of con- trols)

•Press lift lever plunger and raise attachment lift lever to its highest position.

•Release parking brake by depressing brake pedal.

•Place freewheel control in freewheeling position to disengage transmission (See “TO TRANSPORT” in the Operation section of this manual).

•Roll tractor forward off skid.

TO DRIVE TRACTOR OFF SKID (See Opera- tion section for location and function of con- trols)

WARNING: Before starting, read, understand and follow all instructions in the Operation section of this manual. Be sure tractor is in a well-ventilated area. Be sure the area in front of tractor is clear of other people and objects.

7

•Be sure all the above assembly steps have been completed.

•Check engine oil level and fill fuel tank with gasoline.

•Place freewheel control in “transmission engaged” posi- tion.

•Sit on seat in operating position, depress brake pedal and set the parking brake.

•Press lift lever plunger and raise attachment lift lever to its highest position.

•Start the engine. After engine has started, move throttle control to idle position.

•Release parking brake.

•Slowly move the motion control lever forward and slowly drive tractor off skid.

•Apply brake to stop tractor and set parking brake.

•Turn ignition key to “OFF” position.

Continue with the instructions that follow.

ASSEMBLE GAUGE WHEELS AND BRACKETS TO MOWER DECK (See Fig. 4)

The gauge wheels are designed to keep the mower deck in proper position when operating mower. Be sure they are properly adjusted to ensure optimum mower performance.

•Attach front gauge wheel brackets marked front left (FL), front right (FR) to mower deck using (3) carriage bolts and (3) locknuts. For ease of installation do not tighten locknuts until all carriage bolts have been in- stalled.

•Attach rear gauge wheel brackets marked rear left (R L), rear right (RR) to mower deck using (3) carriage bolts and

(3)locknuts. For ease of installation do not tighten locknuts until all carriage bolts have been installed.

•Slide gauge wheel bar down into bracket channel, Be sure that gauge wheel bar aligning holes are on top. Assemble gauge wheels as shown using shoulder bolts, 3/8 washers and 3/8-16 center locknuts and tighten securely.

•Adjust gauge wheels to highest position for ease of mower deck assembly.

•Adjust gauge wheels before operating mower as shown in the operation section of this manual.

RETAINER

SPRINGCROWNLOCK

NUT

PIN

GAUGE

WHEEL

MOUNTING

BRACKET

SHOULDER

BOLT ADJUSTING

BAR

GAUGE	CARRIAGE
WHEEL	BOLTS
3/8 WASHER	3/8-16 CENTER
	LOCKNUT

FIG. 4