SERVICE AND ADJUSTMENTS

•Loosen adjustment bolt in front of the right rear wheel.

•Position the gear shift lever in the neutral (N) posi- tion.

•Tighten adjustment bolt securely.

NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position.

NEUTRAL

LOCK GATE

GEARSHIFT LEVER

ADJUSTMENT

BOLT

FIG. 23

TO ADJUST STEERING WHEEL ALIGN- MENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble per instructions in the Assembly section of this manual.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor. If damage has occurred to affect the front wheel toe-in or camber, contact your nearest authorized service center/department.

TO REMOVE WHEEL FOR REPAIRS (See Fig. 24)

TO START ENGINE WITH A WEAK BATTERY (See Fig. 25)

WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the Maintenance section of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

•Connect one end of the RED cable to the POSITIVE

(+)terminal of each battery(A-B), taking care not to short against tractor chassis.

•Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

•Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

•BLACK cable first from chassis and then from the fully charged battery.

•RED cable last from both batteries.

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

•Repair tire and reassemble.

•On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

WEAK OR DEAD BATTERY

FULLY CHARGED

BATTERY

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

RETAINING WASHERS

RING

AXLE

COVER

SQUARE KEY (REAR

WHEEL ONLY)

FIG. 24

21

FIG. 25

REPLACING BATTERY (See Figs. 26 and 27)

WARNING: Do not short battery terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connect- ing battery, remove metal bracelets, wristwatch bands, rings, etc.

Positive terminal must be connected first to prevent sparking from acci- dental grounding.

•Lift seat pan to raised position.

•Disconnect BLACK battery cable first then RED battery cable and carefully remove battery from tractor.

•Install new battery with terminals in same position as old battery.

Page 20 Page 22
Page 21
Image 21
Poulan 188870 manual To Adjust Steering Wheel ALIGN- Ment, Front Wheel TOE-IN/CAMBER, Replacing Battery See Figs
Page 20 Page 22

188870 specifications

The Poulan 188870 is a powerful and versatile chainsaw designed for both professionals and avid gardeners. Engineered for cutting through various types of wood, from hardwoods to softwoods, the Poulan 188870 showcases a combination of performance and ease of use.

One of the standout features of the Poulan 188870 is its robust engine. It incorporates a 18-inch bar and chain that delivers the necessary power for trimming branches, felling small trees, and cutting firewood. The chainsaw is powered by a reliable 50cc two-stroke engine, which is known for its efficiency and ability to handle tough tasks with minimal downtime.

The design of the Poulan 188870 includes advanced technologies aimed at improving user experience. The chainsaw is equipped with an easy-start feature, allowing for a hassle-free ignition. This saves precious time, particularly in situations where quick operation is essential. The Automatic Oiling System ensures that the chain is adequately lubricated during operation, enhancing performance and extending the lifespan of the bar and chain.

Safety is a significant consideration in the design of the Poulan 188870. It features a chain brake that activates in case of kickback, significantly reducing the risk of accidents. Additionally, with its ergonomic handle, the chainsaw is not only comfortable to hold but also minimizes vibrations, making operations smoother and reducing fatigue during prolonged use.

Another attractive characteristic of the Poulan 188870 is its lightweight construction. Weighing just over 12 pounds, it is relatively easy to maneuver, making it suitable for all-day use without causing excessive strain on the user. This is particularly beneficial for homeowners who may not have extensive experience with power tools.

In terms of maintenance, the Poulan 188870 makes it easy for users to perform routine checks and repairs. The accessible air filter and spark plug facilitate straightforward servicing, which is essential for keeping the chainsaw in optimal working condition.

Overall, the Poulan 188870 combines power, efficiency, and safety features that cater to a wide range of users. It stands out as a reliable choice for anyone in need of a dependable chainsaw for gardening or lumber work. Its balance of performance and user-friendly characteristics makes it a favorite among chainsaw enthusiasts.
Top Page Image Contents