Before Starting the Engine, To Transport See Figs

OPERATION

TO OPERATE MOWER (See Fig. 6)

Your tractor is equipped with an operator presence sens- ing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine. You must remain fully and centrally positioned in the seat to prevent the engine from hesitat- ing or cutting off when operating your equipment on rough, rolling terrain or hills.

•Select desired height of cut.

•Start mower blades by engaging attachment clutch control.

•TO STOP MOWER BLADES - disengage attachment clutch control.

CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped,or the deﬂector shield in place.

ATTACHMENT

LIFT LEVER

HIGH POSITION

TO TRANSPORT (See Figs. 4 and 7)

When pushing or towing your tractor, be sure to disengage transmission by placing freewheel control in freewheeling position. Free wheel control is located at the rear drawbar of tractor.

•Raise attachment lift to highest position with attachment lift control.

•Pull freewheel control out and down into the slot and release so it is held in the disengaged position.

•Do not push or tow tractor at more than two (2) MPH.

•To reengage transmission, reverse above procedure.

NOTE: To protect hood from damage when transporting your tractor on a truck or a trailer, be sure hood is closed and secured to tractor. Use an appropriate means of tying hood to tractor (rope, cord, etc.).

Transmission Engaged

"ENGAGED"

POSITION

LOW POSITION

DEFLECTOR

SHIELD

ATTACHMENT CLUTCH LEVER "DISENGAGED" POSITION

FIG. 6

TO OPERATE ON HILLS

WARNING: Do not drive up or down hills with slopes greater than 15° and do not drive across any slope.

•Choose the slowest speed before starting up or down hills.

•Avoid stopping or changing speed on hills.

•If slowing is necessary, move throttle control lever to slower position.

•If stopping is absolutely necessary, push clutch/brake pedal quickly to brake position and engage parking brake.

•Move motion control lever to neutral (N) position.

IMPORTANT: THE MOTION CONTROL LEVER DOES NOT RETURN TO NEUTRAL (N) POSITION WHEN THE CLUTCH/ BRAKE PEDAL IS DEPRESSED.

•To restart movement, slowly release parking brake and clutch/brake pedal.

•Slowly move motion control lever to slowest setting.

•Make all turns slowly.

Transmission Disengaged

FIG. 7

TOWING CARTS AND OTHER ATTACHMENTS

Tow only the attachments that are recommended by and comply with speciﬁcations of the manufacturer of your trac- tor. Use common sense when towing. Too heavy of a load, while on a slope, is dangerous. Tires can lose traction with the ground and cause you to lose control of your tractor.

BEFORE STARTING THE ENGINE

CHECK ENGINE OIL LEVEL

•The engine in your tractor has been shipped, from the factory, already ﬁlled with summer weight oil.

•Check engine oil with tractor on level ground.

•Remove oil ﬁll cap/dipstick and wipe clean, reinsert the dipstick and screw cap tight, wait for a few seconds, remove and read oil level. If necessary, add oil until “FULL” mark on dipstick is reached. Do not overﬁll.

•For cold weather operation you should change oil for easier starting (See “OIL VISCOSITY CHART” in the Maintenance section of this manual).

•To change engine oil, see the Maintenance section in this manual.

190288 specifications

The Poulan 190288 is a powerful and versatile chainsaw that is designed for both professional landscapers and home users. Renowned for its robustness and reliability, this model exemplifies the perfect balance of performance and ease of use.

One of the standout features of the Poulan 190288 is its 18-inch cutting bar, which provides users with a generous reach, allowing for efficient cutting of medium to large trees and branches. This longer reach translates to reduced time spent on the job, making it an excellent choice for both forestry tasks and property maintenance.

At the heart of the Poulan 190288 is a dependable 42cc engine that delivers remarkable power and torque. This engine is designed to handle tough jobs with ease, whether it's felling trees, limbing, or trimming. The engine also employs advanced technologies that enhance fuel efficiency and reduce emissions, fulfilling environmental standards while delivering excellent performance.

The chainsaw features an automatic oiling system, which ensures that the chain is always lubricated without the need for constant manual adjustment. This not only extends the life of the bar and chain but also allows users to focus on their tasks rather than worrying about maintenance. Additionally, the tool-less chain tensioning system is a significant advantage; it allows for quick adjustments to the chain tension, promoting safety and efficiency during operation.

User comfort is a major consideration in the design of the Poulan 190288. It includes features such as an anti-vibration system, which minimizes fatigue during extended use. The ergonomic handle design ensures a comfortable grip, enhancing overall control and maneuverability.

Maintenance is straightforward thanks to the easy-access air filter and spark plug, making routine upkeep manageable even for those who are less mechanically inclined. The Poulan 190288 is also built to last, with high-quality materials that can withstand harsh working conditions.

In summary, the Poulan 190288 is a well-rounded chainsaw that combines power, efficiency, and user-friendly features. Whether you need it for residential tasks or professional landscaping, this chainsaw is designed to meet a variety of cutting demands while ensuring safety and comfort through innovative design. With its thoughtful engineering and robust construction, the Poulan 190288 stands out as a reliable tool in any woodworker's or landscaper's arsenal.

Poulan 190288 manual Before Starting the Engine, To Operate Mower See Fig, To Transport See Figs

Models: 190288