SERVICE AND ADJUSTMENTS

NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position.

After above adjustment is made, if the tractor still creeps forward or backward while motion control lever is in neutral position, follow these steps:

Loosen the adjustment bolt.

Move the motion control lever 1/4 to 1/2 inch in the direction it is trying to creep.

Tighten adjustment bolt securely.

Start engine and test.

If tractor still creeps, repeat above steps until satis- fied.

MOTION CONTROL

LEVER NEUTRAL LOCK GATE

ADJUSTMENT

BOLT

02239

FIG. 22

TRANSMISSION REMOVAL/REPLACEMENT

Should your transmission require removal for service or replacement, it should be purged after reinstallation and before operating the tractor. See“PURGETRANSMISSION” in the Operation section of this manual.

TO ADJUST STEERING WHEEL

ALIGNMENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble per instructions in the Assembly section of this manual.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor. If damage has occurred to affect the front wheel toe-in or camber, contact your nearest authorized service center/department.

TO REMOVE WHEEL FOR REPAIRS (See Fig. 23)

Block up axle securely.

Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

Repair tire and reassemble.

On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

Replace washers and snap retaining ring securely in axle groove.

Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

WASHERS

RETAINING

RING

AXLE COVER

SQUARE KEY (REAR WHEEL ONLY)

FIG. 23

TO START ENGINE WITH A WEAK BATTERY (See Fig. 24)

WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the MAINTENANCE sec- tion of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

Connect one end of the RED cable to the POSITIVE

(+)terminal of each battery(A-B), taking care not to short against tractor chassis.

Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

BLACK cable first from chassis and then from the fully charged battery.

RED cable last from both batteries.

WEAK OR DEAD BATTERY FULLY CHARGED BATTERY

FIG. 24

REPLACING BATTERY (See Figs. 25 and 26)

WARNING: Do not short battery terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connect- ing battery, remove metal bracelets, wristwatch bands, rings, etc.

Positive terminal must be connected first to prevent sparking from acci- dental grounding.

22

Page 22
Image 22
Poulan 190288 manual Transmission REMOVAL/REPLACEMENT, To Adjust Steering Wheel Alignment, Front Wheel TOE-IN/CAMBER

190288 specifications

The Poulan 190288 is a powerful and versatile chainsaw that is designed for both professional landscapers and home users. Renowned for its robustness and reliability, this model exemplifies the perfect balance of performance and ease of use.

One of the standout features of the Poulan 190288 is its 18-inch cutting bar, which provides users with a generous reach, allowing for efficient cutting of medium to large trees and branches. This longer reach translates to reduced time spent on the job, making it an excellent choice for both forestry tasks and property maintenance.

At the heart of the Poulan 190288 is a dependable 42cc engine that delivers remarkable power and torque. This engine is designed to handle tough jobs with ease, whether it's felling trees, limbing, or trimming. The engine also employs advanced technologies that enhance fuel efficiency and reduce emissions, fulfilling environmental standards while delivering excellent performance.

The chainsaw features an automatic oiling system, which ensures that the chain is always lubricated without the need for constant manual adjustment. This not only extends the life of the bar and chain but also allows users to focus on their tasks rather than worrying about maintenance. Additionally, the tool-less chain tensioning system is a significant advantage; it allows for quick adjustments to the chain tension, promoting safety and efficiency during operation.

User comfort is a major consideration in the design of the Poulan 190288. It includes features such as an anti-vibration system, which minimizes fatigue during extended use. The ergonomic handle design ensures a comfortable grip, enhancing overall control and maneuverability.

Maintenance is straightforward thanks to the easy-access air filter and spark plug, making routine upkeep manageable even for those who are less mechanically inclined. The Poulan 190288 is also built to last, with high-quality materials that can withstand harsh working conditions.

In summary, the Poulan 190288 is a well-rounded chainsaw that combines power, efficiency, and user-friendly features. Whether you need it for residential tasks or professional landscaping, this chainsaw is designed to meet a variety of cutting demands while ensuring safety and comfort through innovative design. With its thoughtful engineering and robust construction, the Poulan 190288 stands out as a reliable tool in any woodworker's or landscaper's arsenal.