SAFETY RULES

SAFE OPERATION PRACTICES FOR RIDE-ON MOWERS

IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH.

I. GENERAL OPERATION

Read, understand, and follow all instructions in the manual and on the machine before starting.

Only allow responsible adults, who are familiar with the instructions, to operate the machine.

Clear the area of objects such as rocks, toys, wire, etc., which could be picked up and thrown by the blade.

Be sure the area is clear of other people before mow- ing. Stop machine if anyone enters the area.

Never carry passengers.

Do not mow in reverse unless absolutely necessary. Al- ways look down and behind before and while backing.

Be aware of the mower discharge direction and do not point it at anyone. Do not operate the mower without either the entire grass catcher or the guard in place.

Slow down before turning.

Never leave a running machine unattended. Always turn off blades, set parking brake, stop engine, and remove keys before dismounting.

Turn off blades when not mowing.

Stop engine before removing grass catcher or un- clogging chute.

Mow only in daylight or good artificial light.

Do not operate the machine while under the influence of alcohol or drugs.

Watch for traffic when operating near or crossing road- ways.

Use extra care when loading or unloading the machine into a trailer or truck.

Data indicates that operators, age 60 years and above, are involved in a large percentage of riding mower-re- lated injuries. These operators should evaluate their ability to operate the riding mower safely enough to protect themselves and others from serious injury.

Keep machine free of grass , leaves or other debris build-up which can touch hot exhaust / engine parts and burn. Do not allow the mower deck to plow leaves or other debris which can cause build-up to occur. Clean any oil or fuel spillage before operating or storing the machine. Allow machine to cool before storage.

II. SLOPE OPERATION

Slopes are a major factor related to loss-of-control and tipover accidents, which can result in severe injury or death. All slopes require extra caution. If you cannot back up the slope or if you feel uneasy on it, do not mow it.

DO:

Mow up and down slopes, not across.

Remove obstacles such as rocks, tree limbs, etc.

Watch for holes, ruts, or bumps. Uneven terrain could overturn the machine. Tall grass can hide obstacles.

Use slow speed. Choose a low gear so that you will not have to stop or shift while on the slope.

Follow the manufacturer’s recommendations for wheel weights or counterweights to improve stability.

Use extra care with grass catchers or other attachments. These can change the stability of the machine.

Keep all movement on the slopes slow and gradual. Do not make sudden changes in speed or direction.

Avoid starting or stopping on a slope. If tires lose trac- tion, disengage the blades and proceed slowly straight down the slope.

DO NOT:

Do not turn on slopes unless necessary, and then, turn slowly and gradually downhill, if possible.

Do not mow near drop-offs, ditches, or embankments. The mower could suddenly turn over if a wheel is over the edge of a cliff or ditch, or if an edge caves in.

Do not mow on wet grass. Reduced traction could cause sliding.

Do not try to stabilize the machine by putting your foot on the ground.

Do not use grass catcher on steep slopes.

III. CHILDREN

Tragic accidents can occur if the operator is not alert to the presence of children. Children are often attracted to the machine and the mowing activity. Never assume that children will remain where you last saw them.

Keep children out of the mowing area and under the watchful care of another responsible adult.

Be alert and turn machine off if children enter the area.

Before and when backing, look behind and down for small children.

Never carry children. They may fall off and be seriously injured or interfere with safe machine operation.

Never allow children to operate the machine.

Use extra care when approaching blind corners, shrubs, trees, or other objects that may obscure vision.

IV. SERVICE

Use extra care in handling gasoline and other fuels. They are flammable and vapors are explosive.

-Use only an approved container.

-Never remove gas cap or add fuel with the engine running. Allow engine to cool before refueling. Do not smoke.

-Never refuel the machine indoors.

-Never store the machine or fuel container inside where there is an open flame, such as a water heater.

Never run a machine inside a closed area.

Keep nuts and bolts, especially blade attachment bolts, tight and keep equipment in good condition.

Never tamper with safety devices. Check their proper operation regularly.

Keep machine free of grass, leaves, or other debris build-up. Clean oil or fuel spillage. Allow machine to cool before storing.

Stop and inspect the equipment if you strike an object. Repair, if necessary, before restarting.

Never make adjustments or repairs with the engine running.

Grass catcher components are subject to wear, dam- age, and deterioration, which could expose moving parts or allow objects to be thrown. Frequently check components and replace with manufacturer's recom- mended parts, when necessary.

Mower blades are sharp and can cut. Wrap the blade(s) or wear gloves, and use extra caution when servicing them.

Check brake operation frequently. Adjust and service as required.

2

Page 2
Image 2
Poulan 191984 manual Safety Rules

191984 specifications

The Poulan 191984 is a powerful and versatile chainsaw that stands out in the realm of outdoor tools. Designed for homeowners and professionals alike, the 191984 is engineered to provide robust performance and user-friendly features, making it an ideal choice for a variety of cutting tasks.

One of the key features of the Poulan 191984 is its efficient engine. The chainsaw is equipped with a reliable 42cc two-stroke engine, delivering ample power for cutting through tough wood with ease. This engine is designed for maximum efficiency, providing excellent fuel economy while maintaining high performance. As a result, users can expect longer operating times between refuels, which is particularly beneficial for those large projects that require sustained cutting.

The Poulan 191984 also incorporates advanced technologies that enhance its usability. A notable feature is its Easy Start technology, which significantly reduces the effort needed to start the chainsaw. This feature is especially valuable for those who may struggle with traditional pull-start mechanisms. Additionally, the chainsaw is equipped with a primer bulb that ensures an easier starting procedure, allowing users to get to work quickly without unnecessary hassle.

Another highlight of the 191984 is its cutting capacity. The chainsaw boasts a 16-inch bar and chain, providing a good balance for various cutting applications, including tree trimming, firewood preparation, and light to medium-duty logging tasks. The design allows for effective cuts while remaining manageable, giving users both power and control.

Safety is a critical consideration in the design of the Poulan 191984. It features a chain brake, which helps prevent accidental chain rotation during operation and contributes to safer handling. The ergonomic handle design ensures comfort during use, reducing fatigue and enhancing control. Additionally, the chainsaw is lightweight, making it easy to maneuver even during extended use.

Maintenance has also been simplified with the Poulan 191984. The tool-free chain tensioning system allows users to adjust the chain tension without the need for additional tools, making adjustments straightforward and quick. The transparent fuel and oil tanks provide visibility into levels, helping users manage their fuel efficiently.

Overall, the Poulan 191984 combines power, efficiency, and safety features that make it a reliable choice for anyone looking for a dependable chainsaw. Whether for homeowners or seasoned professionals, its balanced performance and user-centric design ensure it meets the demands of various cutting tasks effectively.