SERVICE AND ADJUSTMENTS

Loosen adjustment bolt in front of the right rear wheel.

Position the gear shift lever in the neutral (N) posi- tion.

Tighten adjustment bolt securely.

NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position.

NEUTRAL

LOCK GATE

GEARSHIFT LEVER

ADJUSTMENT

BOLT

FIG. 21

TO ADJUST STEERING WHEEL ALIGN- MENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble per instructions in the Assembly section of this manual.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor.If damage has occurred to affect the front wheel toe-in or camber, contact your nearest authorized service center/department.

TO REMOVE WHEEL FOR REPAIRS (See Fig. 22)

TO START ENGINE WITH A WEAK BATTERY (See Fig. 23)

WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the Maintenance section of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

Connect one end of the RED cable to the POSITIVE

(+)terminal of each battery(A-B), taking care not to short against tractor chassis.

Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

BLACK cable first from chassis and then from the fully charged battery.

RED cable last from both batteries.

• Block up axle securely.

• Remove axle cover, retaining ring and washers to allow

wheel removal (rear wheel contains a square key - Do

not lose).

• Repair tire and reassemble.

• On rear wheels only: align grooves in rear wheel hub

and axle. Insert square key.

WEAK OR DEAD BATTERY

FULLY CHARGED

BATTERY

Replace washers and snap retaining ring securely in

 

axle groove.

Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

RETAINING WASHERS

RING

AXLE

COVER

SQUARE KEY (REAR

WHEEL ONLY)

FIG. 22

22

FIG. 23

REPLACING BATTERY (See Figs. 24 and 25)

WARNING: Do not short battery terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connect- ing battery, remove metal bracelets, wristwatch bands, rings, etc.

Positive terminal must be connected first to prevent sparking from acci- dental grounding.

Lift seat pan to raised position.

Disconnect BLACK battery cable first then RED battery cable and carefully remove battery from tractor.

Install new battery with terminals in same position as old battery.

Page 22
Image 22
Poulan 195506 manual To Adjust Steering Wheel ALIGN- Ment, Front Wheel TOE-IN/CAMBER, Replacing Battery See Figs

195506 specifications

The Poulan 195506 is an efficient and robust gas-powered chainsaw designed for both professional and amateur users who require reliable performance for a variety of cutting tasks. This model is particularly noted for its ease of use, making it an excellent choice for homeowners looking to manage their landscaping needs or perform light logging activities.

One of the standout features of the Poulan 195506 is its powerful engine. It is equipped with a 50cc 2-cycle engine, which provides ample power for cutting through tough materials, ensuring that users can tackle everything from tree felling to firewood preparation with ease. The engine's design allows for quick starts and smooth performance, thus minimizing user fatigue during extended operation.

The chainsaw's cutting bar measures 18 inches, offering a fantastic balance between maneuverability and cutting capacity. This length is ideal for a variety of tasks, enabling users to handle both small and medium-sized trees effectively. Furthermore, the bar features a low kickback design, enhancing safety by reducing the chances of dangerous incidents during operation.

Another noteworthy characteristic of the Poulan 195506 is its automated oiling system. This feature ensures that the chain remains adequately lubricated during use, minimizing wear and tear, and prolonging the lifespan of the cutting chain. The oil reservoir is easily accessible, allowing users to refill it quickly without hassle.

In terms of user comfort, the Poulan 195506 is designed with an ergonomic handle that provides a secure grip, reducing vibration and strain during operation. This thoughtful design aspect is especially important for users who may be using the chainsaw for prolonged periods.

Additionally, the chainsaw incorporates several safety features, such as the front hand guard and a chain brake, which activate in the case of kickback, providing an extra layer of security for users. The combination of these safety features, along with its manageable weight, makes the Poulan 195506 a user-friendly choice for those at any skill level.

Overall, the Poulan 195506 is a versatile chainsaw that combines power, safety, and ease of use, making it an essential tool for anyone looking to efficiently handle their outdoor cutting tasks. Its reliable performance, attractive features, and robust construction solidify its place as a favored choice among chainsaw enthusiasts.