MAINTENANCE

TRACTOR

Always observe safety rules when performing any main- tenance.

BRAKE OPERATION

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be checked and adjusted. (See “TO ADJUST BRAKE” in the Service and Adjustments section of this manual).

TIRES

Maintain proper air pressure in all tires (See “PROD- UCT SPECIFICATIONS” section of this manual).

Keep tires free of gasoline, oil, or insect control chemicals which can harm rubber.

Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM AND REVERSE OPERATION SYSTEM (ROS)

Be sure operator presence and reverse operation systems are working properly. If your tractor does not function as described, repair the problem immediately.

The engine should not start unless the brake pedal is fully depressed, and the attachment clutch control is in the disengaged position.

CHECK OPERATOR PRESENCE SYSTEM

When the engine is running, any attempt by the operator to leave the seat without first setting the parking brake should shut off the engine.

When the engine is running and the attachment clutch is engaged, any attempt by the operator to leave the seat should shut off the engine.

The attachment clutch should never operate unless the operator is in the seat.

CHECK REVERSE OPERATION (ROS) SYSTEM

When the engine is running with the ignition switch in the engine "ON" position and the attachment clutch engaged, any attempt by the operator to shift into reverse should shut off the engine.

When the engine is running with the ignition switch in the ROS "ON" position and the attachment clutch engaged, any attempt by the operator to shift into reverse should NOT shut off the engine.

ROS "ON" POSITION

ENGINE "ON" POSITION

 

(NORMAL OPERATING)

828

BLADE CARE

For best results mower blades must be kept sharp. Replace bent or damaged blades.

CAUTION: Use only a replacement blade approved by the manufacturer of your tractor. Using a blade not ap- proved by the manufacturer of your tractor is hazardous, could damage your tractor and void your warranty.

BLADE REMOVAL (See Fig. 8)

Raise mower to highest position to allow access to blades.

Remove blade bolt, lock washer and flat washer securing blade.

Install new or resharpened blade with trailing edge up towards deck as shown.

IMPORTANT: TO ENSURE PROPER ASSEMBLY, CENTER HOLE IN BLADE MUST ALIGN WITH STAR ON MANDREL ASSEMBLY.

Reassemble blade bolt, lock washer and flat washer in exact order as shown.

Tighten blade bolt securely (27-35 Ft. Lbs. torque).

IMPORTANT: BLADE BOLT IS HEATTREATED.IF BOLT NEEDS REPLACING, REPLACE ONLY WITH APPROVE BOLT SHOWN IN THE REPAIR PARTS.

TRAILING

MANDREL

EDGE UP BLADE

ASSEMBLY

CENTER

 

HOLE

 

FLAT WASHER

 

LOCK WASHER

 

 

STAR

BLADE BOLT

 

FIG. 8

 

TO SHARPEN BLADE (See Fig. 9)

NOTE: We do not recommend sharpening blade - but if you do, be sure the blade is balanced.

Care should be taken to keep the blade balanced. An un- balanced blade will cause excessive vibration and eventual damage to mower and engine.

The blade can be sharpened with a file or on a grind- ing wheel. Do not attempt to sharpen while on the mower.

To check blade balance, you will need a 5/8" diameter steel bolt, pin, or a cone balancer. (When using a cone balancer, follow the instructions supplied with balancer.)

NOTE: Do not use a nail for balancing blade. The lobes of the center hole may appear to be centered, but are not.

Slide blade on to an unthreaded portion of the steel bolt or pin and hold the bolt or pin parallel with the ground. If blade is balanced, it should remain in a horizontal

16position. If either end of the blade moves downward, sharpen the heavy end until the blade is balanced.

Page 16
Image 16
Poulan 195506 manual Tractor, Blade Removal See Fig, To Sharpen Blade See Fig

195506 specifications

The Poulan 195506 is an efficient and robust gas-powered chainsaw designed for both professional and amateur users who require reliable performance for a variety of cutting tasks. This model is particularly noted for its ease of use, making it an excellent choice for homeowners looking to manage their landscaping needs or perform light logging activities.

One of the standout features of the Poulan 195506 is its powerful engine. It is equipped with a 50cc 2-cycle engine, which provides ample power for cutting through tough materials, ensuring that users can tackle everything from tree felling to firewood preparation with ease. The engine's design allows for quick starts and smooth performance, thus minimizing user fatigue during extended operation.

The chainsaw's cutting bar measures 18 inches, offering a fantastic balance between maneuverability and cutting capacity. This length is ideal for a variety of tasks, enabling users to handle both small and medium-sized trees effectively. Furthermore, the bar features a low kickback design, enhancing safety by reducing the chances of dangerous incidents during operation.

Another noteworthy characteristic of the Poulan 195506 is its automated oiling system. This feature ensures that the chain remains adequately lubricated during use, minimizing wear and tear, and prolonging the lifespan of the cutting chain. The oil reservoir is easily accessible, allowing users to refill it quickly without hassle.

In terms of user comfort, the Poulan 195506 is designed with an ergonomic handle that provides a secure grip, reducing vibration and strain during operation. This thoughtful design aspect is especially important for users who may be using the chainsaw for prolonged periods.

Additionally, the chainsaw incorporates several safety features, such as the front hand guard and a chain brake, which activate in the case of kickback, providing an extra layer of security for users. The combination of these safety features, along with its manageable weight, makes the Poulan 195506 a user-friendly choice for those at any skill level.

Overall, the Poulan 195506 is a versatile chainsaw that combines power, safety, and ease of use, making it an essential tool for anyone looking to efficiently handle their outdoor cutting tasks. Its reliable performance, attractive features, and robust construction solidify its place as a favored choice among chainsaw enthusiasts.