SERVICE AND ADJUSTMENTS

If distance is other than 1-9/16", loosen jam nut and turn nut “A” until distance becomes 1-9/16". Retighten jam nut against nut “A”.

Engage transmission by placing freewheel control in “transmission engaged” position.

Road test tractor for proper stopping distance as stated above. Readjust if necessary. If stopping distance is still greater than five (5) feet in highest gear, further maintenance is necessary. Replace brake pads or contact a qualified service center.

WITH PARKING BRAKE “ENGAGED”

NUT “A”

1-9/16”

JAM NUT

 

OPERATING

ARM

01513

DO NOT TOUCH THIS NUT. IF FURTHER BRAKE ADJUST- MENT IS NECESSARY CONTACT YOUR NEAREST AUTHO- RIZED SERVICE CENTER/DEPARTMENT

FIG. 24

TO REPLACE MOTION DRIVE BELT (See Fig. 25)

Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest.

BELT REMOVAL -

Remove mower (See “TO REMOVE MOWER” in this section of manual).

NOTE: Observe entire motion drive belt and position of all belt guides and keepers.

Disconnect clutch wire harness.

Remove clutch locator.

Remove belt from stationary idler and clutching idler.

Remove belt downward from engine pulley and around electric clutch.

Pull belt slack toward rear of tractor. Carefully remove belt upwards from transmission input pulley and over cooling fan blades.

Remove belt from center span keeper and pull belt away from tractor.

BELT INSTALLATION -

Carefully work new belt down around transmission cooling fan and onto the input pulley.

Slide belt into the center span keeper.

Pull belt toward front of tractor and roll belt around electric clutch and onto engine pulley.

Install belt through stationary idler and clutching idler.

Reinstall clutch locator and tighten nut securely.

Reconnect clutch harness.

Make sure belt is in all pulley grooves and inside all belt guides and keepers.

Install mower (See “TO INSTALL MOWER” in this sec- tion of manual).

ELECTRIC

CLUTCH LOCATOR

CLUTCH

 

CLUTCHING

IDLER

STATIONARY

IDLER

CENTER SPAN

KEEPER

TRANSMISSION

CLUTCH

INPUT PULLEY

WIRE

 

HARNESS

FIG. 25

TRANSAXLE MOTION CONTROL LEVER NEUTRAL ADJUSTMENT (See Fig. 26)

The motion control lever has been preset at the factory and adjustment should not be necessary.

Loosen adjustment bolt in front of the right rear wheel, and lightly tighten.

Start engine and move motion control lever until tractor does not move forward or backward.

Hold motion control lever in that position and turn engine off.

While holding motion control lever in place, loosen the adjustment bolt.

Move motion control lever to the neutral (N) (lock gate) position.

Tighten adjustment bolt securely.

NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position.

After above adjustment is made, if the tractor still creeps forward or backward while motion control lever is in neutral position, follow these steps:

Loosen the adjustment bolt.

Move the motion control lever 1/4 to 1/2 inch in the direction it is trying to creep.

Tighten adjustment bolt securely.

Start engine and test.

If tractor still creeps, repeat above steps until satis- fied.

24

Page 24
Image 24
Poulan 196712 manual To Replace Motion Drive Belt See Fig, Transaxle Motion Control Lever Neutral Adjustment See Fig

196712 specifications

The Poulan 196712 is a versatile and powerful chainsaw designed to meet the demands of both professional landscapers and avid homeowners alike. Renowned for its durability and reliability, the Poulan 196712 is equipped with numerous features that enhance its performance and ease of use.

At the heart of the Poulan 196712 is a robust 46 cc, 2-cycle engine that delivers ample power while maintaining fuel efficiency. This engine is designed to handle a variety of cutting tasks, from felling small trees to trimming branches and clearing brush. The chainsaw operates at a high RPM, enabling it to cut through tough materials quickly and effortlessly.

One of the standout features of the Poulan 196712 is its anti-vibration technology. This system is designed to reduce the amount of vibration experienced by the user during operation, providing greater comfort and control. With less vibration, users can work for extended periods without fatigue, enhancing productivity and reducing the risk of injury.

The chainsaw features a well-designed air filtration system that helps keep the engine running smoothly. The easily accessible air filter can be cleaned or replaced without the need for special tools, ensuring optimal engine performance and prolonging the life of the chainsaw.

Safety is a top priority with the Poulan 196712. The chainsaw is equipped with a chain brake that engages automatically in the event of kickback, protecting the user from potential harm. Additionally, the front hand guard adds an extra layer of safety, allowing users to work confidently in a variety of conditions.

Another significant feature of the Poulan 196712 is its tool-less chain tensioning system. This feature allows users to adjust the chain tension quickly and easily without the need for additional tools. Proper chain tensioning is critical for optimal performance and safety, making this feature particularly convenient for users who value efficiency.

Finally, the Poulan 196712 boasts a lightweight design, making it easy to maneuver during extended use. Its ergonomic handle provides a comfortable grip, further enhancing user control.

In summary, the Poulan 196712 is a powerful and feature-rich chainsaw that combines performance, safety, and ease of use. With its advanced technologies and thoughtful design, it is an excellent choice for anyone looking to tackle their cutting tasks effectively and efficiently. Whether for professional use or personal projects, the Poulan 196712 stands out as a reliable tool in the world of outdoor equipment.