SAFETY RULES
TRACTOR -- MODEL NUMBER 271470
MOWER DECK
•Use slow speed. Choose a low gear so that you will not have to stop or shift while on the slope.
•Avoid starting or stopping on a slope. If tires lose traction, disengage the blades and proceed slowly straight down the slope.
•If machine stops while going uphill, disengage blades, shift into reverse and back down slowly.
•Do not turn on slopes unless neces- sary, and then, turn slowly and gradu- ally downhill, if possible.
Look for this symbol to point out important safety precautions. It means
CAUTION!!! BECOME ALERT!!! YOUR SAFETY IS INVOLVED.
CAUTION: In order to prevent accidental starting when setting up, transporting, adjusting or making repairs, always disconnect spark plug wire and place wire where it cannot contact spark plug.
CAUTION: Do not coast down a hill in neutral, you may lose control of the tractor.
CAUTION: Tow only the attachments that are recommended by and comply with specifications of the manufacturer of your tractor. Use common sense when towing. Operate only at the lowest possible speed when on a slope. Too heavy of a load, while on a slope, is dangerous. Tires can lose traction with the ground and cause you to lose control of your tractor.
WARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other repro- ductive harm.
WARNING: Battery posts, terminals and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
Wash hands after handling.
KEY | PART |
| KEY | PART |
| |
NO. | NO. | DESCRIPTION | NO. | NO. | DESCRIPTION | |
1 | 170280 | Mower Housing Assembly | 56 | 165723 | Spacer, Retainer | |
2 | 72140506 | Bolt, Carriage | 67 | 149846 | Knob | |
3 | 138017 | Bracket Asm. Fram Sway Bar | 68 | 144200 | Belt | |
4 | 169970 | Bracket, Asm. Deck Sway | 69 | 76020312 | Pin, Cotter 3/32 x 3/4 | |
|
| Bar | 86 | 7631J | Runner, LH | |
5 | 4939M | Retainer, Spring | 87 | 128772 | Runner, RH | |
6 | 130832 | Asm. Suspension Rear | 88 | 19111216 | Washer 11/32 x 3/4 x 16 Ga | |
8 | 850857 | Bolt, Hex | 89 | 19131612 | Washer 13/32 x 1 x 12 Ga | |
9 | 10030600 | Washer, Lock, Hlcl Sprg 3/8 | 107 | 133502 | Spacer, Retainer | |
10 | 140296 | Washer, Hard Blade Mower | 108 | 133503 | Stiffener, Idler Arm | |
|
| Vented | 109 | 74760640 | Bolt, Hex Head | |
11 | 134148 | Blade, Mower, Mulching 38" | 110 | 142587 | Upstop Deck Front 38" | |
13 | 137645 | Shaft and Bearing Assembly | 113 | 17060512 | Screw | |
|
| (Includes Key Number 15) | 122 | 131289 | Rod, Brake, LH | |
14 | 128774 | Mandrel Housing, Vented | 123 | 169971 | Rod, Brake, RH | |
15 | 110485X | Ball Bearing, Mandrel | 146 | 165891 | Bolt Carriage Idler | |
16 | 140329 | Stripper, Mower, Vented | 148 | 169022 | Spring Return Idler | |
19 | 132827 | Bolt, Shoulder | 149 | 165898 | Retainer Spring Yellow Zinc | |
21 | 73680500 | Nut, Crownlock | 150 | 19091216 | Washer 9/32 x 3/4 x 16 Ga. | |
23 | 137607 | Bracket, Mower Deflector | 151 | 169670 | Bracket Clutch | |
24 | 105304X | Cap, Sleeve | 152 | 172758 | Cable Clutch 38 In | |
25 | 123713X | Spring, Deflector | 153 | 169674 | Washer Flat 3/8” Type B | |
26 | 110452X | Nut, Push | 154 | 169675 | Spring Retainer | |
27 | 106736X428 | Shield, Deflector | 155 | 169671 | Spring Retention Lever | |
28 | 19111016 | Washer 11/32 x 3/4 x 16 Ga | 156 | 169672 | Spacer | |
29 | 106735X | Rod, Hinge | 157 | 169669 | Rod Clutch | |
30 | 157722 | Screw, Thdro Washer Hd | 158 | 17720410 | Screw Hex Thd Cut | |
31 | 129963 | Washer, Spacer |
|
| ||
32 | 153532 | Pulley, Mandrel | - - | 130794 | Mandrel Assembly (Includes | |
33 | 137266 | Nut, Flangelock 9/16 |
|
| Key Numbers | |
36 | 131494 | Pulley, Idler, Flat |
|
| 31 and 33) | |
40 | 73680600 | Nut Crownlock | - - | 171665 | Mower Deck, Complete | |
45 | 4497H | Retainer, Spring |
|
|
| |
53 | 130840 | Brake Assembly | NOTE: All component dimensions given in U. S. | |||
54 | 133943 | Washer Hardened | ||||
inches 1 inch = 25.4 mm | ||||||
55 | 133840 | Idler Arm Assembly | ||||
|
|
|
4 | 45 |