Starting, Fueling Engine | Poulan 2250, 2450, 2550, 2550 SE, 2555

FUELING & LUBRICATION

WARNING: Remove fuel cap slow- ly when refueling.

FUELING ENGINE

This engine is certified to operate on unleaded gasoline. Before operation, gasoline must be mixed with a good quality synthetic 2-cycle air-cooled engine oil designed to be mixed at a ratio of 40:1. Poulan/Weed Eater brand synthetic oil is recommended. A 40:1 ratio is obtained by mixing 3.2 ounces (95 ml) of oil with 1 gallon (4 liters) of unleaded gasoline. Included with this saw is a 3.2 ounce container of Poulan/Weed Eater brand synthetic oil. Pour the entire contents of this container into 1 gallon of gasoline to achieve the proper fuel mixture.

DO NOT USE automotive or boat oil. These oils will cause engine damage. When mixing fuel follow the instructions printed on the container. Always read and follow the safety rules listed under HANDLE FUEL WITH CAUTION.

BAR AND CHAIN LUBRICATION

The bar and chain require continuous lubri- cation. Lubrication is provided by the auto- matic oiler system when the oil tank is kept filled. Lack of oil will quickly ruin the bar and chain. Too little oil will cause overheating shown by smoke coming from the chain and/ or discoloration of the bar.

In freezing weather oil will thicken, making it necessary to thin bar and chain oil with a small amount (5 to 10%) of #1 Diesel Fuel or kerosene. Bar and chain oil must be free flowing for the oil system to pump enough oil for adequate lubrication.

Genuine PoulanR bar and chain oil is recommended to protect your unit against excessive wear from heat and friction. PoulanR oil resists high temperature thinning. If PoulanR bar and chain oil is not available, use a good grade SAE 30 oil.

SNever use waste oil for bar and chain lubri-

cation.

SAlways stop the engine before removing the oil cap.

IMPORTANT

Experience indicates that alcohol--blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage for 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See STORAGE section for addi- tional information.

STARTING

WARNING: The chain must not move when the engine runs at idle speed. If the chain moves at idle speed refer to CAR- BURETOR ADJUSTMENT within this manual. Avoid contact with the muffler. A hot muffler can cause serious burns.

To stop the engine move the ON/STOP switch to the STOP position.

To start the engine hold the saw firmly on the ground as illustrated. Make sure the chain is free to turn without contacting any object.

Use only 15 --- 18 inches (38 --- 45 cm) of rope per pull.

Hold saw firmly while pulling starter rope.

Starter rope handle

Left hand on front handle

Right foot through rear handle

IMPORTANT POINTS TO REMEMBER

When pulling the starter rope, do not use the full extent of the rope as this can cause the rope to break. Do not let starter rope snap back. Hold the handle and let the rope rewind slowly.

For cold weather starting, start the unit at FULL CHOKE; allow the engine to warm up before squeezing the throttle trigger.

NOTE: Do not cut material with the choke/ fast idle lever at the FULL CHOKE position.

STARTING A COLD ENGINE (or warm engine after running out of fuel):

NOTE: In the following steps, when the choke/fast idle lever is pulled out to the full extent, the correct throttle setting for starting is set automatically.

ON/STOP SWITCH

(SIDE VIEW)

STOP

1.Move ON/STOP switch to the ON posi- tion.

2.Pull out choke/fast idle to the full extent (to the FULL CHOKE position).

3.Slowly press primer bulb 6 times.

4.Pull the starter rope sharply 5 times with your right hand. Then, proceed to the next step.

NOTE: If the engine sounds as if it is trying to start before the 5th pull, stop pulling and immediately proceed to the next step.

5.Push the choke/fast idle lever in to the HALF CHOKE position.

2250, 2450, 2550, 2550 SE, 2555 specifications

The Poulan Pro chainsaw series, including the models 2250, 2450, 2550, 2550 SE, and 2555, represents a solid choice for both professionals and hobbyists in need of reliable cutting performance. Each model comes with distinct characteristics while sharing common technological innovations that define their functionality and efficiency.

The Poulan 2250 is designed for durability and ease of use. Weighing in at a manageable size, this chainsaw features a 50cc engine that delivers impressive power for a variety of cutting tasks. One of its standout features is the automatic oiler, which ensures that the chain is always lubricated, reducing wear and enhancing performance over time.

Next in line is the Poulan 2450, which further builds on the strengths of its predecessor. This model boasts a larger cutting capacity, facilitating challenges posed by thicker materials. It incorporates an easy-start system often appreciated by users who want to avoid the frustration of hard starts, making it a great option for regular maintenance tasks around the yard.

The Poulan 2550 exhibits an even greater commitment to power and efficiency. With a robust 45cc engine, this model effectively combines cutting power with manageable weight. It features an air filter system that promotes longer intervals between cleaning, making it easier for users to maintain the chainsaw in pristine working condition.

The Poulan 2550 SE takes the versatility up a notch. This model is equipped with an ergonomic design that reduces operator fatigue, especially during extended use. It also includes a specialized vibration dampening system, ensuring a more comfortable experience while cutting, which is particularly beneficial for professionals who rely on their equipment for hours on end.

Lastly, the Poulan 2555 combines all the best features from its predecessors while integrating advanced technologies to enhance user experience. This model is designed for straightforward maintenance, featuring tool-less access to the air filter and spark plug, making it easy for users to perform routine upkeep. Additionally, the 2555 is built with a powerful engine that delivers high torque, enabling efficient cutting of tougher materials.

Overall, the Poulan Pro chainsaw series embodies a tradition of reliability and innovation, suitable for a range of users, from casual gardeners to professional landscapers. With features like automatic oilers, ergonomic designs, and advanced air filtration systems, these chainsaws are tailored to meet the demands of various cutting applications, ensuring that users can tackle their tasks with confidence and ease.

Poulan 2250, 2450, 2550, 2550 SE, 2555 Starting, Fueling Engine, BAR and Chain Lubrication

Models: 2250, 2450, 2550, 2550 SE, 2555