Chute Weldment, Deflector Weldment, Deflector Seal | Poulan 420925

REPAIR PARTS SNOW THROWER - MODEL 961980022 (96198002200) CONTROL PANEL / DISCHARGE CHUTE

5

7

3

14

15

			*13	*10
				*10
				*9
			2	*8
				*8
KEY	PART		4	6
			4
		DESCRIPTION
NO.	NO.	DESCRIPTION
1	404770X428	CHUTE WELDMENT	6
2	178633X428	DEFLECTOR WELDMENT	6	*12
3	420673	DEFLECTOR CONTROL ASSEMBLY		*12
4	420325	DEFLECTOR SEAL
5	414280	KNOB BLACK	1
6	128415	POP RIVET		*11
7	17501010	SCREW 10−24 X .625
*8	179829	SHOULDER SCREW
*9	179246	PLASTIC WASHER
*10	191730	NUT 1/4−20		01.09.002-B
*11	72250505	CARRIAGE BOLT 5/16−18 X .50		01.09.002-B
*11	72250505	CARRIAGE BOLT 5/16−18 X .50
*12	751153	NUT 5/16−18
*13	184505	DEFLECTOR SPRING

14420679 (SERVICE PART) DEFLECTOR CONTROL HEAD

15420672 (SERVICE PART) DEFLECTOR CONTROL CABLE

NOTE:

1.ALL ITEMS INDICATED WITH AN * ARE PROVIDED IN THE BAG OF ITEMS SHIPPED LOOSE WITH PRODUCT.

2.ITEMS 14 AND 15 ARE SERVICE PART NUMBERS TO ALLOW PURCHASE OF INDIVIDUAL ITEMS IF NECESSARY.

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.

26

Image 26

Poulan 420925 Chute Weldment, Deflector Weldment, Deflector Control Assembly, Deflector Seal, Knob Black, POP Rivet

Contents

Model Number Snow Thrower Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Chute Deflector Remote Control Parts Packed Separately in Carton Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Unfold Upper Handle Install Traction Drive Control ROD See Figs Install Auger Control ROD See Figs Check Tire Pressure Install Discharge Chute / Chute Rotator Head See FigInstall Chute Deflector Remote Control See Figs Primer OperationKnow Your Snow Thrower Ignition KEY Meets A.N.S.I. Safety Requirements Deflector remote control lever used to change HOW to USE Your Snow Thrower Stopping To Adjust Skid Plates See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Throw Snow See Fig Check Engine OIL Level See Fig Before Starting the EngineScraper BAR See Fig ADD Gasoline See Fig Before Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has Frozen Maintenance Cleaning Engine Chute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height To Remove Wheels See Fig Remove the klik pin and remove wheel from axle Storage Other Troubleshooting Exploded KEY Part Description CARRIAGEBOLT5/16−18X.625 Auger HousingScrapper BAR Auger Bearing Skid Plate LH Auger Assembly 30 LHAuger Assembly 30 RH Skid Plate RH Plastic Washer Weight BARDrift Cutter BAR Lockwasher 5/16 Rotator Pivot Bracket LEVER/CABLE Rotator AssemblyRotator Head Pulley Pivot Deflector Weldment Deflector Control AssemblyChute Weldment Deflector Seal Panel Bracket LH Plow Handle LHPlow Handle RH Panel Bracket RH Heated Handle Grip Control Lever RH Control PanelControl Lever LH Traction ROD ARM Carriage Bolt 5/16−18 X 155377 NUT 5/16−18 169675 Console Panel Black Grip SwitchWire Harness Headlight Bezel Repair Parts Snow Thrower Model 961980022 96198002200 Drive Item 43 Exploded END Plate Speed Selector AssemblyDrive Plate Assembly Bottom PAN Frame Safety Ignition KEYENGINE, TEC, Model Engine Mount Plate Impeller Belt Belt CoverTraction Belt Cable Bracket RH Wheel Assembly LHCable Bracket LH Pivot Bracket CoverSteering Bracket Wheel Driver Wrench Power CordRetainer PIN Remote Spring KEY Part Limited Warranty