Console Panel Black, Headlight Bezel, Grip Switch | Poulan 420925

REPAIR PARTS SNOW THROWER - MODEL 961980022 (96198002200) HANDLES

	KEY	PART	DESCRIPTION
	NO.	NO.	DESCRIPTION
	1	413927	CONSOLE PANEL BLACK	3
	2	178668	HEADLIGHT BEZEL	3	8
	2	178668	HEADLIGHT BEZEL
	3	178666	HALOGEN HEADLIGHT
	3	178666	HALOGEN HEADLIGHT		2
	4	184471	SHOULDER SCREW 10−24 X .625		2
	5	175262	SCREW 10−24 X 1.25
	6	417760	GRIP SWITCH
	7	405699	WIRE HARNESS
	8	401620	BULB
				7	5
				7

16

4

5

4

01.10.004-B

1

4

3

4

4

01.05.002-B

KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION

1419797X479 LOWER HANDLE

2405784X479 PIVOT SUPPORT WELDMENT

3150078 SCREW 5/16−18 X .750

417000616 SCREW 3/8−16 X 1.00

2

3

4

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.

30

Image 30

Poulan 420925 Console Panel Black, Headlight Bezel, Halogen Headlight, Shoulder Screw 10−24 X, Grip Switch, Wire Harness

Contents

Model Number Snow Thrower Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Chute Deflector Remote Control Parts Packed Separately in Carton Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Unfold Upper Handle Install Traction Drive Control ROD See Figs Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotator Head See Fig Install Chute Deflector Remote Control See FigsCheck Tire Pressure Primer OperationKnow Your Snow Thrower Ignition KEY Meets A.N.S.I. Safety Requirements Deflector remote control lever used to change HOW to USE Your Snow Thrower Stopping To Adjust Skid Plates See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Throw Snow See Fig Check Engine OIL Level See Fig Before Starting the EngineScraper BAR See Fig ADD Gasoline See Fig Before Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has Frozen Maintenance Cleaning Engine Service and Adjustments To Adjust Snow Thrower HeightChute Deflector To Remove Wheels See Fig Remove the klik pin and remove wheel from axle Storage Other Troubleshooting Exploded KEY Part Description CARRIAGEBOLT5/16−18X.625 Auger HousingScrapper BAR Auger Bearing Skid Plate LH Auger Assembly 30 LHAuger Assembly 30 RH Skid Plate RH Plastic Washer Weight BARDrift Cutter BAR Lockwasher 5/16 Rotator Pivot Bracket LEVER/CABLE Rotator AssemblyRotator Head Pulley Pivot Deflector Weldment Deflector Control AssemblyChute Weldment Deflector Seal Panel Bracket LH Plow Handle LHPlow Handle RH Panel Bracket RH Heated Handle Grip Control Lever RH Control PanelControl Lever LH Traction ROD ARM Carriage Bolt 5/16−18 X 155377 NUT 5/16−18 169675 Console Panel Black Grip SwitchWire Harness Headlight Bezel Repair Parts Snow Thrower Model 961980022 96198002200 Drive Item 43 Exploded END Plate Speed Selector AssemblyDrive Plate Assembly Bottom PAN Frame Safety Ignition KEYENGINE, TEC, Model Engine Mount Plate Belt Cover Traction BeltImpeller Belt Wheel Assembly LH Cable Bracket LHCable Bracket RH Pivot Bracket CoverSteering Bracket Wheel Driver Wrench Power CordRetainer PIN Remote Spring KEY Part Limited Warranty