Manuals / Poulan / Lawn and Garden / Snow Blower

Poulan 421602 REPAIR PARTS SNOW THROWER - - MODEL NUMBER PR208 DRIVE, Part, Description

Models: 421602

1 40

Download 40 pages 42.18 Kb

Page 32

Image 32

REPAIR PARTS SNOW THROWER - - MODEL NUMBER PR208 (96192002100)

DRIVE

	6
1b	4
7	3
	3
1b
6	1a

	3
5	4

KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION
1	188226	(assy of 1a,1b) AXLE ASSEMBLY
1a	179352	AXLE SHAFT
1b	184206	ROLL PIN 3/16
2	402691	SPROCKET
3	174697	THRUST WASHER
4	179830	BEARING
5	17490508	BOLT 5/16−18 X .500
6	155443	CLIK PIN
7	189282	SQUARE KEY

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.

Failure to do so could be hazardous, damage your snow thrower and void your warranty.

Page 32

Image 32

Poulan 421602 owner manual REPAIR PARTS SNOW THROWER - - MODEL NUMBER PR208 DRIVE, Part, Description

Contents

SNOW THROWER IMPORTANT MANUALPR208 Do Not Throw AwaySafe Operation Practices for Walk-Behind Snow Throwers TrainingPreparation OperationTABLE OF CONTENTS PRODUCT SPECIFICATIONSMaintenance and Storage CUSTOMER RESPONSIBILITIESASSEMBLY / PRE-OPERATION HOW TO SET UP YOUR SNOW THROWERPARTS PACKED SEPARATELY IN CARTON REMOVE SNOW THROWER FROM CARTONUNFOLD UPPER HANDLE ASSEMBLY / PRE-OPERATIONINSTALL SPEED CONTROL ROD See Figs. 1 and ASSEMBLY / PRE-OPERATION INSTALL AUGER CONTROL ROD See Figs. 5 andINSTALL DISCHARGE CHUTE / CHUTE ROTATER HEAD See Fig CHECK TIRE PRESSUREOPERATION KNOW YOUR SNOW THROWERRecoil auxiliary starter handle - used for starting the engine MEETS A.N.S.I. SAFETY REQUIREMENTSOPERATION HOW TO USE YOUR SNOW THROWER OPERATIONSTOPPING TO USE FUEL SHUT-OFF VALVE See FigUSING THE CLEAN-OUT TOOL See Fig TO ADJUST SKID PLATES See FigOPERATION TO THROW SNOW See FigBEFORE STARTING THE ENGINE OPERATIONSCRAPER BAR See Fig CHECK ENGINE OIL LEVEL See FigSNOW THROWING TIPS OPERATIONTO START ENGINE BEFORE STOPPINGMAINTENANCE GENERAL RECOMMENDATIONSBEFORE EACH USE LUBRICATIONCLEANING ENGINEMAINTENANCE BELTSSERVICE AND ADJUSTMENTS 1. Be sure the on/off switch is in the OFF position2. Remove safety ignition key TO ADJUST SNOW THROWER HEIGHTSERVICE AND ADJUSTMENTS TO REPLACE BELTS See FigSTORAGE OTHERENGINE SNOW THROWERTROUBLESHOOTING Loss of powerDoes not start Engine idles orSERVICE NOTES REPAIR PARTS SNOW THROWER - - MODEL NUMBER PR208 AUGER HOUSING / IMPELLER ASSEMBLYNOTE All component dimensions given in U.S. inches. 1 inch = 25.4 mm 01.07.004-BREPAIR PARTS SNOW THROWER - - MODEL NUMBER PR208 AUGER HOUSING / IMPELLER ASSEMBLYPART DESCRIPTIONREPAIR PARTS SNOW THROWER - - MODEL NUMBER PR208 AUGER HOUSING / IMPELLER ASSEMBLYPART DESCRIPTIONREPAIR PARTS SNOW THROWER - - MODEL NUMBER PR208 AUGER HOUSING / IMPELLER ASSEMBLYPART DESCRIPTIONCONTROL PANEL / CHUTE REPAIR PARTS SNOW THROWER - - MODEL NUMBER PR208PART DESCRIPTIONREPAIR PARTS SNOW THROWER - - MODEL NUMBER PR208 CONTROL PANEL / CHUTEPART DESCRIPTIONREPAIR PARTS SNOW THROWER - - MODEL NUMBER PR208 HANDLES PARTDESCRIPTION PART01.08.002-E REPAIR PARTS SNOW THROWER - - MODEL NUMBER PR208 HANDLESPART DESCRIPTIONREPAIR PARTS SNOW THROWER - - MODEL NUMBER PR208 HANDLES PARTDESCRIPTION 01.12.001-A01.10.001-B REPAIR PARTS SNOW THROWER - - MODEL NUMBER PR208 HANDLESPART DESCRIPTIONREPAIR PARTS SNOW THROWER - - MODEL NUMBER PR208 DRIVE 01.02.006-EREPAIR PARTS SNOW THROWER - - MODEL NUMBER PR208 DRIVE PARTDESCRIPTION PARTDESCRIPTION REPAIR PARTS SNOW THROWER - - MODEL NUMBER PR208 DRIVEPART CHASSIS / ENGINE / PULLEYS REPAIR PARTS SNOW THROWER - - MODEL NUMBER PR20801.00.030 PART01.04.025-A REPAIR PARTS SNOW THROWER - - MODEL NUMBER PR208CHASSIS / ENGINE / PULLEYS PARTREPAIR PARTS SNOW THROWER - - MODEL NUMBER PR208 WHEELS WHEEL ASSEMBLY LHWHEEL ASSEMBLY RH PARTREPAIR PARTS SNOW THROWER - - MODEL NUMBER PR208 BAG OF PARTS SAFETY IGNITION KEYPART DESCRIPTIONDESCRIPTION REPAIR PARTS SNOW THROWER - - MODEL NUMBER PR208 DECALSPART SERVICE NOTES SERVICE NOTES LIMITED WARRANTY