Manuals / Poulan / Lawn and Garden / Snow Blower

Poulan 421602 REPAIR PARTS SNOW THROWER - - MODEL NUMBER PR208, Auger Housing / Impeller Assembly

Models: 421602

1 40

Download 40 pages 42.18 Kb

Page 22

Image 22

REPAIR PARTS SNOW THROWER - - MODEL NUMBER PR208 (96192002100)

AUGER HOUSING / IMPELLER ASSEMBLY

KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION
1	404928X428	AUGER HOUSING
2	404931X479	SCRAPPER BAR
3	72270505	CARRIAGE BOLT 5/16−18 X .625
4	155377	NUT 5/16−18

3 (5x) 4 (5x)

01.07.001-A

2	3

		KEY	PART	DESCRIPTION
		NO.	NO.	DESCRIPTION
		1	420478	AUGER BEARING
3		2	411939	BEARING PLUG
	01.07.024-B	3	179582	SCREW 5/16−18 X 1.00
	01.07.024-B

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.

Failure to do so could be hazardous, damage your snow thrower and void your warranty.

Page 22

Image 22

Poulan 421602 REPAIR PARTS SNOW THROWER - - MODEL NUMBER PR208, Auger Housing / Impeller Assembly, Part, Description

Contents

PR208 SNOW THROWERIMPORTANT MANUAL Do Not Throw AwayPreparation Safe Operation Practices for Walk-Behind Snow ThrowersTraining OperationMaintenance and Storage TABLE OF CONTENTSPRODUCT SPECIFICATIONS CUSTOMER RESPONSIBILITIESPARTS PACKED SEPARATELY IN CARTON ASSEMBLY / PRE-OPERATIONHOW TO SET UP YOUR SNOW THROWER REMOVE SNOW THROWER FROM CARTONINSTALL SPEED CONTROL ROD See Figs. 1 and ASSEMBLY / PRE-OPERATIONUNFOLD UPPER HANDLE INSTALL DISCHARGE CHUTE / CHUTE ROTATER HEAD See Fig ASSEMBLY / PRE-OPERATIONINSTALL AUGER CONTROL ROD See Figs. 5 and CHECK TIRE PRESSUREOPERATION KNOW YOUR SNOW THROWEROPERATION MEETS A.N.S.I. SAFETY REQUIREMENTSRecoil auxiliary starter handle - used for starting the engine STOPPING HOW TO USE YOUR SNOW THROWEROPERATION TO USE FUEL SHUT-OFF VALVE See FigOPERATION USING THE CLEAN-OUT TOOL See FigTO ADJUST SKID PLATES See Fig TO THROW SNOW See FigSCRAPER BAR See Fig BEFORE STARTING THE ENGINEOPERATION CHECK ENGINE OIL LEVEL See FigTO START ENGINE SNOW THROWING TIPSOPERATION BEFORE STOPPINGBEFORE EACH USE MAINTENANCEGENERAL RECOMMENDATIONS LUBRICATIONMAINTENANCE CLEANINGENGINE BELTS2. Remove safety ignition key SERVICE AND ADJUSTMENTS1. Be sure the on/off switch is in the OFF position TO ADJUST SNOW THROWER HEIGHTSERVICE AND ADJUSTMENTS TO REPLACE BELTS See FigENGINE STORAGEOTHER SNOW THROWERDoes not start TROUBLESHOOTINGLoss of power Engine idles orSERVICE NOTES NOTE All component dimensions given in U.S. inches. 1 inch = 25.4 mm REPAIR PARTS SNOW THROWER - - MODEL NUMBER PR208AUGER HOUSING / IMPELLER ASSEMBLY 01.07.004-BPART REPAIR PARTS SNOW THROWER - - MODEL NUMBER PR208AUGER HOUSING / IMPELLER ASSEMBLY DESCRIPTIONPART REPAIR PARTS SNOW THROWER - - MODEL NUMBER PR208AUGER HOUSING / IMPELLER ASSEMBLY DESCRIPTIONPART REPAIR PARTS SNOW THROWER - - MODEL NUMBER PR208AUGER HOUSING / IMPELLER ASSEMBLY DESCRIPTIONPART CONTROL PANEL / CHUTEREPAIR PARTS SNOW THROWER - - MODEL NUMBER PR208 DESCRIPTIONPART REPAIR PARTS SNOW THROWER - - MODEL NUMBER PR208CONTROL PANEL / CHUTE DESCRIPTIONDESCRIPTION REPAIR PARTS SNOW THROWER - - MODEL NUMBER PR208 HANDLESPART PARTPART 01.08.002-EREPAIR PARTS SNOW THROWER - - MODEL NUMBER PR208 HANDLES DESCRIPTIONDESCRIPTION REPAIR PARTS SNOW THROWER - - MODEL NUMBER PR208 HANDLESPART 01.12.001-APART 01.10.001-BREPAIR PARTS SNOW THROWER - - MODEL NUMBER PR208 HANDLES DESCRIPTIONREPAIR PARTS SNOW THROWER - - MODEL NUMBER PR208 DRIVE 01.02.006-EDESCRIPTION REPAIR PARTS SNOW THROWER - - MODEL NUMBER PR208 DRIVEPART PARTPART REPAIR PARTS SNOW THROWER - - MODEL NUMBER PR208 DRIVEDESCRIPTION 01.00.030 CHASSIS / ENGINE / PULLEYSREPAIR PARTS SNOW THROWER - - MODEL NUMBER PR208 PARTCHASSIS / ENGINE / PULLEYS 01.04.025-AREPAIR PARTS SNOW THROWER - - MODEL NUMBER PR208 PARTWHEEL ASSEMBLY RH REPAIR PARTS SNOW THROWER - - MODEL NUMBER PR208 WHEELSWHEEL ASSEMBLY LH PARTPART REPAIR PARTS SNOW THROWER - - MODEL NUMBER PR208 BAG OF PARTSSAFETY IGNITION KEY DESCRIPTIONPART REPAIR PARTS SNOW THROWER - - MODEL NUMBER PR208 DECALSDESCRIPTION SERVICE NOTES SERVICE NOTES LIMITED WARRANTY