OPERATION

TO START ENGINE

•Be sure fuel shut-off valve is in the “OPEN” position.

Your snow thrower engine is equipped with both a 120 Volt A.C. electric starter and a recoil starter. The electric starter is equipped with a three-wire power cord and plug and is designed to operate on 120 Volt A.C. household current.

•Be sure your house is a 120 Volt A.C. three-wire grounded system. If you are uncertain, consult a licensed electrician.

WARNING: Do not use the electric starter if your house is not a 120 Volt A.C. three-wire grounded system. Seri- ous personal injury or damage to your snow thrower could result.

COLD START - ELECTRIC STARTER

1.Insert safety ignition key (tied to recoil start cord) into ignition slot until it clicks. DO NOT turn the key. Keep the extra safety ignition key in a safe place.

2.Place ON / OFF switch in “ON” position.

3.Move choke control to “FULL” position.

4.Connect the power cord to the engine.

5.Plug the other end of the power cord into a three-hole grounded 120 Volt A.C. receptacle.

NOTE: Do not use primer when starting engine with the electric starter.

6. Push starter button until engine starts.

IMPORTANT: Do not crank engine more than five continu- ous seconds between each time you try to start. Wait 5 to 10 seconds between each attempt.

7.When the engine starts, release the starter button and slowly move the choke control to the “OFF” position.

8.Disconnect the power cord from the receptacle first, then from the engine.

Allow the engine to warm up for a few minutes. Engine will not develop full power until it has reached normal operat- ing temperature.

WARM START - ELECTRIC STARTER

Follow the steps above, keeping the choke control in the “OFF” position.

COLD START - RECOIL STARTER

1.Insert safety ignition key (tied to recoil start cord) into ignition slot until it clicks. DO NOT turn the key. Keep the extra safety ignition key in a safe place.

2.Place ON / OFF switch in “ON” position.

3.Rotate choke control to “FULL” position.

4.Push the primer four (4) times if the temperature is below 15°F, or two (2) times if temperature is between 15° and 50°F. If temperature is above 50°F, priming is not necessary.

NOTE: Over priming may cause flooding, preventing the engine from starting. If you do flood the engine, wait a few minutes before attempting to start and DO NOT push the primer.

5.Pull recoil starter handle quickly. Do not allow starter rope to snap back.

6.When the engine starts, release the recoil starter handle and slowly move the choke control to the “OFF” posi- tion.

Allow the engine to warm up for a few minutes. Engine will not develop full power until it has reached normal operat- ing temperature.

WARM START - RECOIL STARTER

Follow the steps above, keeping the choke in the “OFF” position. DO NOT push the primer.

BEFORE STOPPING

Run the engine for a few minutes to help dry off any mois- ture on the engine.

IF RECOIL STARTER HAS FROZEN

If the recoil starter has frozen and will not turn the engine, proceed as follows:

1.Grasp the recoil starter handle and slowly pull as much rope out of the starter as possible.

2.Release the recoil starter handle and let it snap back against the starter.

If the engine still fails to start, repeat the above steps or use the electric starter.

SNOW THROWING TIPS

•Go slower in deep, freezing or heavy wet snow. Use the drive speed control, NOT the ON / OFF switch, to adjust speed.

•It is easier and more efficient to remove snow imme- diately after it falls.

•The best time to remove snow is the early morning. At this time the snow is usually dry and has not been ex- posed to the direct sun and warming temperatures.

•Slightly overlap each successive path to ensure all snow will be removed.

•Throw snow downwind whenever possible.

•Adjust the skid plates to proper height for current snow conditions. See “TO ADJUST SKID PLATES” in this section of this manual.

•For extremely heavy snow, reduce the width of snow removal by overlapping previous path and moving slowly.

•Keep engine clean and clear of snow during use. This will help air flow and extend engine life.

•After snow-throwing is completed, allow engine to run for a few minutes to melt snow and ice off the engine.

•Clean the entire snow thrower thoroughly after each use and wipe dry so it is ready for next use.

WARNING: Do not operate snow thrower if weather conditions impair visibility. Throwing snow during a heavy, windy snowstorm can blind you and be hazardous to the safe operation of the snow thrower.

13

Page 12 Page 14
Page 13
Image 13
Poulan 96192003200, 428553, PP1330ES Snow Throwing Tips, To Start Engine, Before Stopping, If Recoil Starter has Frozen
Page 12 Page 14

PR1330ES, PP1330ES, 96192003200, 428553 specifications

The Poulan PP1330ES is a powerful and reliable chainsaw designed for both homeowners and professionals alike. Known for its robust performance, this model features a 33cc two-cycle engine which delivers ample power for a variety of cutting tasks. Whether trimming branches or tackling larger logs, the PP1330ES is up to the job.

One of its standout features is the effortless pull starting system. The EZ Start technology minimizes the effort required to start the engine, ensuring that users can get to work without the frustration that often accompanies traditional pull-start mechanisms. This is especially beneficial for those who may not be as physically strong or are new to using chainsaws.

The chainsaw incorporates a 16-inch cutting bar, which provides a great balance between portability and cutting capacity. This length is ideal for medium-sized trees and logs, making the PP1330ES versatile for various outdoor tasks. The chainsaw also comes with an automatic oiling system, which lubricates the chain during operation, enhancing both performance and longevity. This feature ensures that users spend less time on maintenance and more time cutting.

Safety is paramount in chainsaw design, and the PP1330ES does not disappoint. It includes a chain brake that initiates instantly in the event of kickback, protecting the user from potential accidents. The handle is ergonomically designed, providing a comfortable grip that reduces fatigue, allowing for extended use without discomfort.

Model 428553, part of the Poulan Pro series, features similar attributes and is engineered for durability. The inclusion of a heavy-duty air filter prolongs engine life by reducing debris, while the easy-access filter hastens maintenance checks.

The PR1330ES and model 96192003200 are also worth mentioning; both are designed with features that enhance performance and user experience. These models utilize advanced technologies like improved vibration dampening systems, which reduce operator fatigue during prolonged use, and innovative air injection systems that minimize airborne debris.

In summary, the Poulan PP1330ES, along with 428553, PR1330ES, and 96192003200, showcases a range of features that prioritize power, performance, and user safety. These chainsaws are equipped with technologies that enhance ease of use and maintenance, making them ideal for anyone looking to tackle outdoor cutting tasks efficiently and effectively. Whether you’re a weekend warrior or a seasoned professional, these Poulan chainsaws are sure to meet your needs.
Top Page Image Contents