Manuals / Poulan / Lawn and Garden / Snow Blower

Poulan XT827ES, 428863, 96192003400 owner manual Drive, Part, Description

Models: XT827ES 96192003400 428863

1 40

Download 40 pages 3.86 Kb

Page 32

Image 32

REPAIR PARTS SNOW THROWER - - MODEL NUMBER XT827ES (96192003400)

DRIVE

	6
1b	4
7	3
	3
1b
6	1a

				KEY	PART	DESCRIPTION
				NO.	NO.	DESCRIPTION
			2	1	188226	(assy of 1a,1b) AXLE ASSEMBLY
			2	1a	179352	AXLE SHAFT
		3		1a	179352	AXLE SHAFT
		3		1b	9465M1	ROLL PIN 3/16
5	4			1b	9465M1	ROLL PIN 3/16
5	4		01.03.005-B	2	402691	SPROCKET
			01.03.005-B	3	174697	THRUST WASHER
				3	174697	THRUST WASHER
				4	179830	BEARING
				5	17490508	BOLT 5/16−18 X .500
				6	155443	CLIK PIN
				7	189282	SQUARE KEY

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.

Failure to do so could be hazardous, damage your snow thrower and void your warranty.

Page 32

Image 32

Poulan XT827ES, 428863, 96192003400 owner manual Drive, Part, Description

Contents

OWNERS MANUAL MODEL NUMBER SNOW THROWERIMPORTANT MANUAL XT827ESOperation TrainingPreparation TABLE OF CONTENTS PRODUCT SPECIFICATIONSMaintenance and Storage CUSTOMER RESPONSIBILITIESREMOVE SNOW THROWER FROM CARTON ASSEMBLY / PRE-OPERATIONPARTS PACKED SEPARATELY IN CARTON HOW TO SET UP YOUR SNOW THROWER ASSEMBLY / PRE-OPERATIONINSTALL SPEED CONTROL ROD See Figs. 1 and TOOL BOX See Fig.CHECK TIRE PRESSURE ASSEMBLY / PRE-OPERATIONINSTALL AUGER CONTROL ROD See Figs. 5 and OPERATION KNOW YOUR SNOW THROWERMEETS A.N.S.I. SAFETY REQUIREMENTS OPERATIONHOW TO USE YOUR SNOW THROWER OPERATIONSTOPPING TO USE CHOKE CONTROL See Fig.USING THE CLEAN-OUTTOOL See Fig. TO ADJUST SKID PLATES See Fig.OPERATION TO THROW SNOW See Fig.BEFORE STARTING THE ENGINE OPERATIONSCRAPER BAR See Fig. CHECK ENGINE OIL LEVEL See Fig.SNOW THROWING TIPS OPERATIONBEFORE STOPPING IF RECOIL STARTER HAS FROZENMAINTENANCE GENERAL RECOMMENDATIONSBEFORE EACH USE LUBRICATIONCLEANING ENGINEMAINTENANCE BELTSSERVICE AND ADJUSTMENTS 2.Remove safety ignition keyTO ADJUST SNOW THROWER HEIGHT SNOW THROWERSERVICE AND ADJUSTMENTS TO REPLACE BELTS See Fig.SERVICE AND ADJUSTMENTS TO ADJUST CABLE TENSION See Fig.ENGINE TO REMOVE WHEELS See Fig.STORAGE OTHERSNOW THROWER ENGINETROUBLESHOOTING Loss of powerDoes not start Engine idles orAUGER HOUSING / IMPELLER ASSEMBLY DESCRIPTION AUGER HOUSING / IMPELLER ASSEMBLYPART AUGER HOUSING / IMPELLER ASSEMBLY PARTDESCRIPTION PARTAUGER HOUSING / IMPELLER ASSEMBLY PARTDESCRIPTION PARTDESCRIPTION CONTROL PANEL / CHUTEPART CONTROL PANEL / CHUTE PARTDESCRIPTION NOTESHANDLES PARTDESCRIPTION PARTHANDLES 1412683X479 CONTROL PANELHANDLES PARTDESCRIPTION 180480HANDLES PARTDESCRIPTION 183346DRIVE DRIVE PARTDESCRIPTION PARTDESCRIPTION DRIVEPART CHASSIS / ENGINE / PULLEYS 2 3 1PART DESCRIPTIONCHASSIS / ENGINE / PULLEYS PARTDESCRIPTION PARTWHEELS WHEEL ASSEMBLY LHPART DESCRIPTIONBAG OF PARTS SAFETY IGNITION KEY01.14.007-A PARTDECALS 1 4 1PART DESCRIPTIONSERVICE NOTES SERVICE NOTES LIMITED WARRANTY