Bag Of Parts, 01.14.007-A, Description, 193071 | Poulan 428863

BAG OF PARTS

REPAIR PARTS SNOW THROWER - - MODEL NUMBER XT827ES (96192003400)

BAG OF PARTS

3

		4	5	KEY	PART
				KEY	PART	DESCRIPTION
				NO.	NO.	DESCRIPTION
				1	198563	POWER CORD
				2	169675	RETAINER PIN
				3	180684X008	WRENCH
				4	73800600	LOCKNUT 3/8−16
	2	1	7	5	19131316	WASHER 3/8
	2			6	192090	SHEAR BOLT 1/4−20 X 1−3/4
				6	192090	SHEAR BOLT 1/4−20 X 1−3/4
		6		7	73800400	LOCKNUT 1/4−20
		01.14.004-B

	KEY	PART	DESCRIPTION
	NO.	NO.	DESCRIPTION
1	1	193071	SAFETY IGNITION KEY
1

01.14.007-A

13

4

1	4
	2.56

2

		2
01.14.012-A
KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION

1180445 SHIFTER ROD TOP

2187716 SHIFTER ROD BOTTOM

372270505 CARRIAGE BOLT 5/16-18 X .75

4

155377

NUT 5/16-18

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 36

Image 36

Poulan 428863, 96192003400, XT827ES owner manual Bag Of Parts, 01.14.007-A, Description, 193071, Safety Ignition Key

Contents

OWNERS MANUAL MODEL NUMBER SNOW THROWERIMPORTANT MANUAL XT827ES Training PreparationOperation TABLE OF CONTENTS PRODUCT SPECIFICATIONSMaintenance and Storage CUSTOMER RESPONSIBILITIES ASSEMBLY / PRE-OPERATION PARTS PACKED SEPARATELY IN CARTONREMOVE SNOW THROWER FROM CARTON HOW TO SET UP YOUR SNOW THROWER INSTALL SPEED CONTROL ROD See Figs. 1 andTOOL BOX See Fig. UNFOLD UPPER HANDLE INSTALL AUGER CONTROL ROD See Figs. 5 and CHECK TIRE PRESSURE OPERATION KNOW YOUR SNOW THROWER MEETS A.N.S.I. SAFETY REQUIREMENTS HOW TO USE YOUR SNOW THROWER STOPPINGTO USE CHOKE CONTROL See Fig. TO CONTROL SNOW DISCHARGE See Figs. 10 & USING THE CLEAN-OUTTOOL See Fig. TO ADJUST SKID PLATES See Fig.TO THROW SNOW See Fig TO MOVE FORWARD AND BACKWARD See Fig. BEFORE STARTING THE ENGINE SCRAPER BAR See Fig.CHECK ENGINE OIL LEVEL See Fig. ADD GASOLINE See Fig. SNOW THROWING TIPS BEFORE STOPPINGIF RECOIL STARTER HAS FROZEN MAINTENANCE GENERAL RECOMMENDATIONSBEFORE EACH USE LUBRICATION CLEANING ENGINEBELTS AUGER GEAR CASE SERVICE AND ADJUSTMENTS 2.Remove safety ignition keyTO ADJUST SNOW THROWER HEIGHT CHUTE DEFLECTOR TO REPLACE BELTS See Fig. TO ADJUST CABLE TENSION See Fig. TO REMOVE WHEELS See Fig.CARBURETOR ENGINE SPEED STORAGE OTHERFUEL SYSTEM ENGINE OIL TROUBLESHOOTING Loss of powerDoes not start Engine idles or AUGER HOUSING / IMPELLER ASSEMBLY PART DESCRIPTION AUGER HOUSING / IMPELLER ASSEMBLY PARTDESCRIPTION PART AUGER HOUSING / IMPELLER ASSEMBLY CONTROL PANEL / CHUTE NOTES HANDLES 1412683X479 CONTROL PANEL 180480 183346 DRIVE DRIVE PARTDESCRIPTION PART DRIVE CHASSIS / ENGINE / PULLEYS 2 3 1423185X505 ENGINE MOUNTING PLATE CHASSIS / ENGINE / PULLEYS WHEELS WHEEL ASSEMBLY LH187833X428 187865X428 BAG OF PARTS SAFETY IGNITION KEY01.14.007-A 193071 DECALS 1 4 1181037 DECAL, DANGER SERVICE NOTES SERVICE NOTES LIMITED WARRANTY