193071, Safety Ignition KEY | Poulan 429837, 96192003401 instruction

REPAIR PARTS SNOW THROWER - - MODEL NUMBER XT827ES (96192003401)

BAG OF PARTS

	4	5	KEY	PART
			KEY	PART	DESCRIPTION
			NO.	NO.	DESCRIPTION
			1	198563	POWER CORD
			2	169675	RETAINER PIN
			3	180684X008	WRENCH
			4	73800600	LOCKNUT 3/8−16
2	1	7	5	19131316	WASHER 3/8
2			6	192090	SHEAR BOLT 1/4−20 X 1−3/4
			6	192090	SHEAR BOLT 1/4−20 X 1−3/4
	6		7	73800400	LOCKNUT 1/4−20
	01.14.004-B

	KEY	PART	DESCRIPTION
	NO.	NO.	DESCRIPTION
1	1	193071	SAFETY IGNITION KEY
1

01.14.007-A

1	4
	2.56

		2
01.14.012-A
KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION

1180445 SHIFTER ROD TOP

2187716 SHIFTER ROD BOTTOM

372270505 CARRIAGE BOLT 5/16-18 X .75

155377

NUT 5/16-18

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 36

Page 36

Image 36

Poulan 429837, 96192003401 owner manual 193071, Safety Ignition KEY

Contents

Model Number Snow Thrower Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Assembly / PRE-OPERATION Parts Packed Separately in CartonRemove Snow Thrower from Carton HOW to SET UP Your Snow Thrower Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Tool BOX See Fig Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotater Head See FigCheck Tire Pressure Operation Know Your Snow ThrowerPrimer Traction Meets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engine HOW to USE Your Snow Thrower StoppingTo USE Choke Control See Fig To Control Snow Discharge See Figs Using the CLEAN-OUT Tool See Fig To Adjust Skid Plates See FigTo Throw Snow See Fig To Move Forward and Backward See Fig Before Starting the Engine Scraper BAR See FigCheck Engine OIL Level See Fig ADD Gasoline See Fig Snow Throwing Tips Before StoppingIf Recoil Starter has Frozen Maintenance General RecommendationsBefore Each USE Lubrication Cleaning Engine Service and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See Fig To Replace Belts See Fig To Adjust Cable Tension See Fig To Remove Wheels See FigCarburetor Engine Speed Storage OtherFuel System Engine OIL Troubleshooting 23 22 KEY Part Description Auger Housing Scraper BARAuger 27 LH Auger 27 RH Auger Bearing Bearing Plug Chute Weldment Deflector WeldmentDeflector Seal Strap LEVER/CABLE Rotator Assembly Cable Assembly AdjustableCable Assembly Heat Shield Rotator Head Loop Handle LH Loop Handle RHLower Tube Pivot Support Spacer RetainerKnob RED Handle Knob Impeller ROD Assembly Traction ROD AssemblyShifter ROD TOP Shifter ROD Bottom Wire Harness Console PanelHeadlight Bezel Flood Headlight Repair Parts Snow Thrower - Model Number XT827ES Drive Speed Selector Assembly Drive Plate AssemblyWheel HUB END Plate Axle Shaft Roll PIN 3/16Sprocket Clik PIN Frame 423185X505Engine Mounting Plate 428684 Impeller Belt Traction BeltIdler ARM Bracket Idler Pulley Wheel Assembly LH 187833X428187865X428 Safety Ignition KEY 193071 181037 DECAL, DangerDECAL, DANGER, Deflector Service Notes Service Notes Limited Warranty

KEY

WASHER 3/8

KEY

193071

SAFETY IGNITION KEY

01.14.007-A

KEY

1180445 SHIFTER ROD TOP

2187716 SHIFTER ROD BOTTOM