HOW to SET UP Your Snow Thrower | Poulan 96192003401, 429837

ASSEMBLY / PRE-OPERATION

HOW TO SET UP YOUR SNOW THROWER

TOOL BOX (See Fig. 8)

A toolbox is provided on your snow thrower. The toolbox is located on top of the belt cover. Store the extra shear bolts, nuts and multi-wrench provided in parts bag in the toolbox.

NOTE: The multi-wrench may be used for assembly of the chute rotator head to snow thrower and making adjustments to the skid plates.

UNFOLD UPPER HANDLE

1.Raise upper handle to the operating position and tighten handle knobs securely. Additional carriage bolts, washers and handle knobs are in bag of parts. Use to secure upper handle to lower handle. Install in lower holes in handles.

SPEED

CONTROL

ROD

PLASTIC TIE

UPPER

HANDLE

HANDLE

KNOB

LOWER

HANDLE

FIG. 1

SPEED CONTROL ROD
		RETAINER
		SPRING
SPEED		SPEED
CONTROL	CONTROL
BRACKET		LEVER
FIG. 2		5

INSTALL SPEED CONTROL ROD (See Figs. 1 and 2)

1.Remove plastic tie securing rod to lower handle.

2.Insert rod into speed control bracket and secure with retainer spring.

INSTALL TRACTION DRIVE CONTROL ROD (See Figs. 3 and 4)

The traction drive control rod is installed on the snow thrower.

1.Remove plastic tie securing rod to lower handle.

2.With top end of rod positioned under left side of control panel, push rod down and insert top end of rod into hole in drive control bracket. Secure with retainer spring.

PLASTIC TIE

TRACTION DRIVE

CONTROL ROD

VINYL

SLEEVE

FIG. 3

TRACTION DRIVE	RETAINER
CONTROL LEVER	SPRING
	TRACTION
	DRIVE
	CONTROL
	ROD
DRIVE
CONTROL
BRACKET

FIG. 4

Image 5

Poulan 96192003401, 429837 owner manual HOW to SET UP Your Snow Thrower, Tool BOX See Fig, Unfold Upper Handle

Contents

Snow Thrower Model Number Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Assembly / PRE-OPERATIONParts Packed Separately in Carton Install Speed Control ROD See Figs HOW to SET UP Your Snow ThrowerInstall Traction Drive Control ROD See Figs Tool BOX See Fig Check Tire Pressure Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotater Head See Fig Know Your Snow Thrower OperationPrimer Traction Recoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety Requirements Stopping HOW to USE Your Snow ThrowerTo USE Choke Control See Fig To Control Snow Discharge See Figs To Adjust Skid Plates See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig To Move Forward and Backward See Fig Scraper BAR See Fig Before Starting the EngineCheck Engine OIL Level See Fig ADD Gasoline See Fig If Recoil Starter has Frozen Snow Throwing TipsBefore Stopping General Recommendations MaintenanceBefore Each USE Lubrication Engine Cleaning To Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See Fig To Replace Belts See Fig To Remove Wheels See Fig To Adjust Cable Tension See FigCarburetor Engine Speed Other StorageFuel System Engine OIL Troubleshooting 23 22 KEY Part Description Scraper BAR Auger HousingAuger 27 LH Auger 27 RH Bearing Plug Auger Bearing Deflector Weldment Chute WeldmentDeflector Seal Strap Cable Assembly Adjustable LEVER/CABLE Rotator AssemblyCable Assembly Heat Shield Rotator Head Loop Handle RH Loop Handle LHLower Tube Pivot Support Retainer SpacerKnob RED Handle Knob Traction ROD Assembly Impeller ROD AssemblyShifter ROD TOP Shifter ROD Bottom Console Panel Wire HarnessHeadlight Bezel Flood Headlight Repair Parts Snow Thrower - Model Number XT827ES Drive Drive Plate Assembly Speed Selector AssemblyWheel HUB END Plate Roll PIN 3/16 Axle ShaftSprocket Clik PIN 423185X505 FrameEngine Mounting Plate 428684 Traction Belt Impeller BeltIdler ARM Bracket Idler Pulley 187865X428 Wheel Assembly LH187833X428 193071 Safety Ignition KEY DECAL, DANGER, Deflector 181037DECAL, Danger Service Notes Service Notes Limited Warranty