Control Panel / Discharge Chute, Part | Poulan 96192003302, 430355

REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES (96192003302)

CONTROL PANEL / DISCHARGE CHUTE

KEY	PART
NO.	NO.	DESCRIPTION

	1	420315X505	CHUTE WELDMENT
	2	178633X505	DEFLECTOR WELDMENT
	3	420325	DEFLECTOR SEAL
	4	179096X479	STRAP
	5	189713X428	KNOB BLACK
	6	128415	POP RIVET
	7	185600	SHOULDER BOLT 1/4−20 X .704
	8	72270505	CARRIAGE BOLT 5/16−18 X .625
01.09.001-B	9	191730	NUT 1/4−20
	10	155415	WASHER
	11	179246	PLASTIC WASHER

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 25

Page 25

Image 25

Poulan 96192003302 REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES, Control Panel / Discharge Chute, Part, Description

Contents

SNOW THROWER OWNERS MANUAL MODEL NUMBERIMPORTANT MANUAL XT824ES Training Safe Operation Practices for Walk-Behind Snow ThrowersPreparation Operation PRODUCT SPECIFICATIONS TABLE OF CONTENTSMaintenance and Storage CUSTOMER RESPONSIBILITIES HOW TO SET UP YOUR SNOW THROWER ASSEMBLY / PRE-OPERATIONPARTS PACKED SEPARATELY IN CARTON REMOVE SNOW THROWER FROM CARTON INSTALL TRACTION DRIVE CONTROL ROD See Figs. 3 and INSTALL SPEED CONTROL ROD See Figs. 1 andUNFOLD UPPER HANDLE INSTALL DISCHARGE CHUTE / CHUTE ROTATOR HEAD See Fig INSTALL AUGER CONTROL ROD See Figs. 5 andCHECK TIRE PRESSURE KNOW YOUR SNOW THROWER OPERATION Recoil auxiliary starter handle - used for starting the engine MEETS A.N.S.I. SAFETY REQUIREMENTS STOPPING HOW TO USE YOUR SNOW THROWERTO USE CHOKE CONTROL See Fig TO CONTROL SNOW DISCHARGE See Figs TO THROW SNOW See Fig USING THE CLEAN-OUT TOOL See FigTO MOVE FORWARD AND BACKWARD See Fig AUGER CONTROL LEVER TO ADJUST SKID PLATES See Fig BEFORE STARTING THE ENGINESCRAPER BAR See Fig CHECK ENGINE OIL LEVEL See Fig TO START ENGINE SNOW THROWING TIPSBEFORE STOPPING IF RECOIL STARTER HAS FROZEN LUBRICATION CHART MAINTENANCEGENERAL RECOMMENDATIONS BEFORE EACH USE ENGINE CLEANINGAUGER GEAR CASE TRACTION DRIVE SYSTEM 1. Be sure the on/off switch is in the OFF position SERVICE AND ADJUSTMENTS2. Remove safety ignition key TO ADJUST SNOW THROWER HEIGHT TO REPLACE BELTS See Fig TO REMOVE WHEELS See Fig TO ADJUST CABLE TENSION See FigCARBURETOR ENGINE SPEED OTHER STORAGEFUEL SYSTEM ENGINE OIL Loss of power TROUBLESHOOTINGDoes not start Engine idles or AUGER HOUSING / IMPELLER ASSEMBLY REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES01.07.026-C 2 EXPLODED DESCRIPTION PART AUGER HOUSING / IMPELLER ASSEMBLY REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ESPART DESCRIPTION AUGER HOUSING / IMPELLER ASSEMBLY 01.09.010-B CONTROL PANEL / DISCHARGE CHUTE CONTROL PANEL / DISCHARGE CHUTE 01.10.019 REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES HANDLES PART 01.08.002-F 01.12.001-E HANDLES 42 EXPLODED REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES DRIVE01.02.013-A PART assy of 1a,1b AXLE ASSEMBLY 423185X505 CHASSIS / ENGINE / PULLEYSENGINE MOUNTING PLATE 428684 CHASSIS / ENGINE / PULLEYS WHEEL ASSEMBLY RH REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES WHEELS SAFETY IGNITION KEY REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES BAG OF PARTS193071 181037 DECALSDECAL, DANGER SERVICE NOTES SERVICE NOTES LIMITED WARRANTY

Poulan 96192003302, 430355 REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES, Part, Description

Models: 96192003302 430355