Chassis / Engine / Pulleys, Part, Description

REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES (96192003302)

CHASSIS / ENGINE / PULLEYS

KEY	PART
NO.	NO.	DESCRIPTION
- -	- - - - - -	B&S ENGINE MODEL
01.00.034-A		12A114-8354-E8
1	418694X505	FRAME
2	150406	BOLT 3/8-16
3	428867	SCREW 5/16-18 X .750

1	KEY	PART
	KEY	PART
	NO.	NO.	DESCRIPTION
	1	423185X505	ENGINE MOUNTING PLATE

01.01.007-A

KEY	PART
NO.	NO.	DESCRIPTION
1	428684	COVER ASSEMBLY

01.21.013-B

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.

Page 33

Image 33

Poulan 96192003302 Chassis / Engine / Pulleys, REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES, Part, Description, 428684

Contents

SNOW THROWER OWNERS MANUAL MODEL NUMBERIMPORTANT MANUAL XT824ES Training Safe Operation Practices for Walk-Behind Snow ThrowersPreparation Operation PRODUCT SPECIFICATIONS TABLE OF CONTENTSMaintenance and Storage CUSTOMER RESPONSIBILITIES HOW TO SET UP YOUR SNOW THROWER ASSEMBLY / PRE-OPERATIONPARTS PACKED SEPARATELY IN CARTON REMOVE SNOW THROWER FROM CARTON INSTALL SPEED CONTROL ROD See Figs. 1 and INSTALL TRACTION DRIVE CONTROL ROD See Figs. 3 andUNFOLD UPPER HANDLE INSTALL AUGER CONTROL ROD See Figs. 5 and INSTALL DISCHARGE CHUTE / CHUTE ROTATOR HEAD See FigCHECK TIRE PRESSURE KNOW YOUR SNOW THROWER OPERATION Recoil auxiliary starter handle - used for starting the engine MEETS A.N.S.I. SAFETY REQUIREMENTS STOPPING HOW TO USE YOUR SNOW THROWERTO USE CHOKE CONTROL See Fig TO CONTROL SNOW DISCHARGE See Figs TO THROW SNOW See Fig USING THE CLEAN-OUT TOOL See FigTO MOVE FORWARD AND BACKWARD See Fig AUGER CONTROL LEVER TO ADJUST SKID PLATES See Fig BEFORE STARTING THE ENGINESCRAPER BAR See Fig CHECK ENGINE OIL LEVEL See Fig TO START ENGINE SNOW THROWING TIPSBEFORE STOPPING IF RECOIL STARTER HAS FROZEN LUBRICATION CHART MAINTENANCEGENERAL RECOMMENDATIONS BEFORE EACH USE ENGINE CLEANINGAUGER GEAR CASE TRACTION DRIVE SYSTEM 1. Be sure the on/off switch is in the OFF position SERVICE AND ADJUSTMENTS2. Remove safety ignition key TO ADJUST SNOW THROWER HEIGHT TO REPLACE BELTS See Fig TO REMOVE WHEELS See Fig TO ADJUST CABLE TENSION See FigCARBURETOR ENGINE SPEED OTHER STORAGEFUEL SYSTEM ENGINE OIL Loss of power TROUBLESHOOTINGDoes not start Engine idles or AUGER HOUSING / IMPELLER ASSEMBLY REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES01.07.026-C 2 EXPLODED DESCRIPTION PART AUGER HOUSING / IMPELLER ASSEMBLY REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ESPART DESCRIPTION AUGER HOUSING / IMPELLER ASSEMBLY 01.09.010-B CONTROL PANEL / DISCHARGE CHUTE CONTROL PANEL / DISCHARGE CHUTE 01.10.019 REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES HANDLES PART 01.08.002-F 01.12.001-E HANDLES REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES DRIVE 42 EXPLODED01.02.013-A PART assy of 1a,1b AXLE ASSEMBLY 423185X505 CHASSIS / ENGINE / PULLEYSENGINE MOUNTING PLATE 428684 CHASSIS / ENGINE / PULLEYS WHEEL ASSEMBLY RH REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES WHEELS REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES BAG OF PARTS SAFETY IGNITION KEY193071 DECALS 181037DECAL, DANGER SERVICE NOTES SERVICE NOTES LIMITED WARRANTY