SERVICE AND ADJUSTMENTS

2. Place gear shift lever in neutral (N) position.

The rear wheels must lock and skid when you try to manually push the tractor forward. If the rear wheels rotate, then the brakeneedstobeserviced.Contactaqualifiedservicecenter.

TOREPLACEMOTIONDRIVEBELT(SeeFig.20)

Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest.

BELT REMOVAL -

Remove mower (See “TO REMOVE MOWER” in this section of manual).

NOTE: Observe entire motion drive belt and position of all belt guides and keepers.

Remove belt from stationary idler and clutching idler.

Remove belt downward from around engine pulley.

Pull belt slack toward rear of tractor. Remove belt up- wards from transaxle pulley by deflecting belt keepers.

Remove belt from center span keeper and pull belt away from tractor.

BELT INSTALLATION -

Carefully work new belt down between transaxle belt keepers and onto the input pulley.

Slide belt into the center span keeper.

Pull belt toward front of tractor and roll around the top groove of engine pulley.

Install belt through stationary idler and clutching idler.

Make sure belt is in all pulley grooves and inside all belt guides and keepers.

Install mower (See “TO INSTALL MOWER” in this section of manual).

ENGINE PULLEY

CLUTCHING

IDLER

STATIONARY

IDLER

CENTER SPAN

KEEPER

TRANSAXLE

PULLEY

FIG. 20

TRANSAXLE GEAR SHIFT LEVER NEUTRAL ADJUSTMENT (See Fig. 21)

The transaxle should be in neutral when the gear shift lever is in neutral (lock gate) position. The adjustment is preset at the factory; however, if adjustment is needed, proceed as follows:

Make sure transaxle is in neutral.

NOTE: When the tractor rear wheels move freely, the transaxle is in neutral.

Loosen adjustment bolt in front of the right rear wheel.

Position the gear shift lever in the neutral position.

Tighten adjustment bolt securely.

NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position.

GEARSHIFT

NEUTRAL

LEVER

LOCK

 

GATE

 

ADJUSTMENT

 

BOLT

FIG. 21

TO ADJUST STEERING WHEEL ALIGNMENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble per instructions in the Assembly section of this manual.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor. If damage has occurred to affect the front wheel toe-in or camber, contact your nearest authorized service center/department.

TO REMOVE WHEEL (See Fig. 22)

Block up axle securely.

Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

Repair tire and reassemble.

On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

Replace washers and snap retaining ring securely in axle groove.

Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

AXLE

RETAINING WASHERS

RING

COVER

 

SQUARE KEY (REAR WHEEL ONLY)

FIG. 22

TO START ENGINE WITH A WEAK BATTERY (See Fig. 23)

WARNING: Lead-acid batteries generate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the Maintenance section

19of this manual).

Page 19
Image 19
Poulan 433401 manual To Adjust Steering Wheel Alignment, Front Wheel TOE-IN/CAMBER

433401 specifications

The Poulan 433401 is a remarkable chainsaw that embodies a blend of power, efficiency, and user-friendly design. Ideal for both professionals and DIY enthusiasts, this model is thoughtfully engineered to handle a variety of cutting tasks, from felling trees to pruning shrubs.

One of the most notable features of the Poulan 433401 is its powerful engine. Equipped with a 33cc two-stroke engine, it delivers ample power while maintaining a lightweight build, which is critical for maneuverability during extended usage. The engine's design allows for efficient fuel consumption, enabling users to maximize their cutting time without frequent refueling. This is particularly useful for those who take on larger jobs or require extended operational periods.

The chainsaw boasts a 16-inch guide bar, making it suitable for a range of cutting applications. The length strikes a balance between efficient cutting and ease of control, making it perfect for both seasoned users and those new to chainsaw operation. The Oregon chain enhances cutting performance, providing smooth and reliable operation while ensuring a clean cut.

One of the standout technologies incorporated into the Poulan 433401 is its automatic oiling system. This essential feature ensures that the chain remains adequately lubricated during operation, reducing friction and wear. The automatic system not only enhances the lifespan of the chain and bar but also ensures optimal performance, allowing users to focus on the task at hand rather than constant maintenance.

Safety features are paramount in the design of the Poulan 433401. It includes a chain brake designed to stop the chain in an event of kickback, which is a common risk when using chainsaws. Additionally, the front and rear handles are ergonomically designed, providing a comfortable grip and reducing user fatigue. This attention to ergonomics helps improve precision and control, particularly during prolonged use.

The Poulan 433401 is also relatively easy to start, thanks to its spring-assisted starter mechanism and purge bulb feature. This makes it accessible to users of all skill levels, eliminating the frustrations often associated with starting smaller engine chainsaws.

Overall, the Poulan 433401 combines power, versatility, and safety. Its innovative design and user-centric features make it a reliable tool for various cutting tasks, setting it apart as a favorable choice in the chainsaw market. Whether for forestry professionals or homeowners looking to maintain their landscapes, the Poulan 433401 stands out as a valuable asset.